Iphone 4s stuck on itunes string. What to do if the iPhone is stuck on the cord. Recovery mode - normal

After unsuccessful flashing on the device screen, you may encounter such a problem as the iTunes icon and USB cable. If you updated via iTunes, then you will see in it the number of the error that occurred during the firmware update. Below are some kinds of errors that may appear in iTunes.

Deciphering iTunes errors in which the phone shows “connect to iTunes”

Error 1

Causes :
You are trying to downgrade a firmware that is not supported by your device or iTunes.
Solution :
Make sure you are using the correct firmware for your phone, and use the appropriate iTunes for the firmware you want to upgrade to.

Mistake 2

Causes :
The problem with ASR, usually occurs with custom firmware with hack and unlock in which a bad ASR Patch is used (Sn0wBreeze under 1.7 had this problem)
Solution:
Use a different firmware.

Mistake 3

Causes :
The problem is most likely in the modem part.
Solution:
It is necessary to carry out diagnostics in the Service Center

Error 4

Causes :
iTunes cannot connect to Apple service servers
Solution:
Most likely you need to check the connection to the Apple servers. You should also pay attention to the hosts file, in the WIndows folder and, if possible, comment out the “#” lines with different IP addresses.

Error 5.6

Causes :
The firmware cannot be installed, either because the boot logos are damaged, or because the device is entered in the wrong service mode
Solution:
A very rare error, you can avoid it by restarting the device in DFU mode and downloading the firmware via iTunes by clicking the Restore iPhone/iPad button

Error 8

Causes :
The difference in the firmware for the device, also the error itself rarely “pops up”, in most cases error 3194 appears
Solution:
Try to substitute a different version of the firmware, since most likely the previous firmware is no longer signed

Error 9

Causes:
Kernel Panic is a kernel error during flashing, an analogue of BSOD (Blue Screen of Death) on Windows.
Solution:
It also occurs with custom firmware. It is worth rebuilding them or using others.

Error 10

Causes:
There is no LLB (Low Level Bootloader) in the firmware, without it the system becomes impossible to boot.
Solution:
Do not use custom firmware without modem upgrade from older versions of PWNage Tools and Sn0wBreeze.

Error 11

Causes:
The firmware lacks BBFW.
Solution:
Use another, or add the missing file to IPSW through the archiver.

Error 13

Causes :
There is a problem with the USB cable or connector on the device itself, and the error also appears when you try to install the beta version of ios
Solution:
Look for damage in the bottom dock of your gadget, as well as on the cable itself with which you are trying to flash the device. If you are trying to upgrade to a beta version, try to use a different one or if possible use OS X to install such firmware.

Error 14

Causes:
Problem with firmware after jailbreak, try to restore with custom firmware If it does not help, the problem is in USB.
Solution:
Restoring from custom firmware, or changing port \ computer

Error 17

Causes:
You are trying to “Update” a custom to another custom.
Solution:
You need to “Restore”, preferably from DFU or Recovery.

Error 20

Causes:
The device was initially put into Recovery Mode and failed to go into DFU
Solution:
It is necessary from the very beginning to start the device in DFU mode and re-update the device

Error 23

Causes:
Usually a hardware error. It is also expressed by the fact that the phone cannot find out the IMEI or MAC address.
Solution:
Take it to a service center, or if you are satisfied with an iPod without WiFi and BlueTooth, then it will be flashed using iTunes 9.0.2 and these instructions

Error 26

Causes:
NOR failed version checking.
Solution:
Change the firmware file.

Error 28

Causes:
Problem with device memory.

Error 27 and 29

Causes:
Cyclic error when restoring in iTunes 8-9.1
Solution:
Use the latest iTunes or any version of iTunes for Mac.

Error 31

Causes:
The device cannot exit DFU mode
Solution:
Most likely there is a hardware problem with the device itself, for this you need to diagnose the gadget

Error 37

Causes:
LLB in the firmware has been replaced with an analogue from another device model.
Solution:
Rebuild custom or use another one.

Error 39, 40 and 10054

Causes:
Problem with access to activation and signing servers. Also, with error 40, there may be a problem with Nand memory, processor or RAM.
Solution:
Try disabling the firewall and antivirus and flash again. If the error persists, then you need to take the device to the Service Center for diagnostics, since most likely the problem is in the hardware.

Error 10**

Causes:
Occurs when downgrade / upgrade to a baseband different from what the firmware has. This doesn't mean the restore failed - it just tells you that the phone's firmware doesn't match the baseband.
Solution:
Use The Frimeware Umbrella to turn on the phone after an error (Kick Device Out of Recovery).

Mistakes 6 and 10

Causes:
Occurs due to a problem with your firmware - usually if you use the wrong boot/recovery logo.
On firmware 2.0, error #6 may mean that you are not in DFU
Solution:
Flash to a new custom firmware and use the correct boot / recovery logo or even standard ones.

Error 1600 and 1611

Causes:
Custom firmware is not designed for DFU.
Solution:
Use Recovery Mode

Errors 16**

Causes:
The system for checking signatures of firmware files is not disabled.
Solution:
It is necessary to jailbreak before installing custom, if you used Spirit you must also disable signature verification manually. To do this, install the Spirit2PWN package from Cydia.
JailbreakME.com is not suitable for installing custom firmware.
If you are customizing iOS 4.1 and higher from PWNage Tools, then you need PWNed DFU - we do it through RedSn0w or PWNage Tools

Error 1619

Causes:
iTunes can't get into your iPhone. it is too old to work with your device
Solution:
Update iTunes.

Error 1644

Causes:
Interruption of the firmware reading session.
Solution:
Do not touch the firmware file while iTunes is restoring your phone, make sure kheubt programs do not manipulate this file.

Error 2005

Causes:
Error in iPhone responses. As a rule, it is caused by mechanical damage.
Solution:
Check your dock.

Error 3004

Causes:
Internet connection required for flashing
Solution:
Make sure your computer is connected to the Internet and there is nothing preventing iTunes from using this connection.

Errors 14**

Causes:
Corrupted firmware file. Or a USB port.
Solution:
– Download the firmware file from another source.
– Replace wire, port, computer.

Mistakes 20**

Causes:
Data cable or usb port failure
Solution:
Change Data-cable, USB ports, if possible, try another computer.

Errors 3014

Causes:
Too long response time from Apple activation server
Solution:
It is necessary to restart the computer / laptop, as well as “reboot” the Internet connection

Error (-39)

Causes:
iTunes can't download purchased music from the iTunes Store
Solution:
1) Install iTunes version 9 or higher.
2) If you are using Web accelerators, turn them off and restart your computer.

Error (-3221)

Causes:
iTunes cannot contact the iTunes Store due to file lock.
Solution:
Change the permissions and permissions of iTunes and iTunesHelper to unlock their ability to send data to the remote server.

Error (-50)

Causes:
The error occurs after the timeout of the sent request.
Can be called:
-Brownman
- Firewall
-AD filters
-Antiviruses
Solution:
If you have any of the programs listed above, set them up so that iTunes can contact itunes.apple.com and ax.itunes.apple.com
If an error occurs while loading video content.
Delete the download video cache, it is in
Mac:
~/Music/iTunes/iTunes Music/Downloads
Note: The tilde (~) refers to your Home directory.

Windows Vista:
\Users\username\Music\iTunes\iTunes Music\Downloads\

Windows XP and 2000:
\Documents and Settings\username\My Documents\My Music\iTunes\iTunes Music\Downloads\

Find the downloaded video file, its extension will be TEMP (*.tmp)
Start downloading from the beginning.

Error 9808

Causes:
iTunes Store Registration Error
Solution:
Start - Control Panel - Internet Options - Advanced and check the items SSL 3.0 and TLS 1.0.
After restart your computer

Error 39

Causes:
Error when trying to sync photos.
Solution:
Try to create a new album in iphoto.
Keep the album blank and only sync iphone with this new album.
This will delete any photos that you have synced to the iphone.
Now put some photos in a new album and sync iphone.
If the sync went well, add a few more photos and sync your iphone.
Keep going through this process until you get the same error.
If you get the same error, then you know that one or more photos in the last batch are causing the error.

Error 13001

Causes:
Broken iTunes library file
Solution:
Create a new itunes library file - by deleting it and then opening itunes and it will re-create it iTunes Library.itl

Errors 13014, 13136, 13213

Causes:
Software hole in iTunes
Solution:
Solution 1
Make sure you have the latest version of iTunes installed on your computer.
Solution 2
Close and reopen iTunes. If the problem persists, restart your computer.

Errors -1

Causes:
Error in the modem part of the device
Solution:
It is necessary to diagnose the device in the Service Center, since this error cannot be solved using the repair software.
Directions to Apple Service on Sumska 82:

If you have any questions. You can contact us - Online consultant or by calling the phone numbers below. We will be glad to help you.

Our address:
Kharkiv, Sumskaya street 82

Schedule:
Monday - Saturday from 10:00 to 20:00
Sunday - from 11:00 to 17:00

Sometimes it happens that the iPhone freezes and the iTunes logo is visible on it, which indicates the start of the firmware recovery process. After a certain time, the phone will update the software and return to normal operation. But in some situations, the USB cable icon appears on the screen, the gadget refuses to work, and many do not know how to fix it and what to do in such a case. Let's look at the main causes of this annoying error and how to fix it.

Why is this happening?

The well-known rule says “the best defense is an attack” and, accordingly, at the beginning it is necessary to find out the cause of this problem. Why iphone stuck on itunes cord in this mode? In addition to software updates, it can also be:

• Software failure (installing new software solves the problem);
• Processor failure;
• Mechanical damage or after an impact (maybe some part has broken that does not allow the iPhone to work);
• The power microcircuit has failed (after impact or contact with moisture).

Each problem requires an individual solution.

Method 1 - Forced reboot of the device

One of the most common reasons is a software update. If you updated the phone firmware shortly before the problem appeared, then you should wait for the recovery to finish and automatically reboot, or force it to be solved. For this, a hard reset is used.

This method of "fixing" the recovery mode differs depending on the model of the Apple device, but will help in a situation where the iPhone is stuck on a cord.

For iPhone 8 and newer, press and immediately release the Volume Up and Volume Down buttons, then press the Home button. Hold it until you see the Apple logo.

For iPhone 7 Plus, press the Power button and the volume down rocker simultaneously, respectively, until the company logo appears. If the iPhone 6 is stuck on a cord or an iPhone of another model, you should simultaneously hold down the Home button and the power button. The drawing should disappear and then the iPhone comes to life.

Method 2 – Fix iPhone Stuck on iTunes with iTunes

If method number 1 did not help you, iphone stuck in recovery mode and you saw a notification that the phone needs to be restored via iTunes, then follow these instructions. This is an easy process, and first you need to connect the device to your computer and run the program. Then the phone should start the treatment itself. If this does not happen, hold down Home and Power until the iTunes icon appears on the device screen.

Then click "Update" and wait for the operation to complete. By choosing this function, you can save data on the iPhone, but if you select "Restore", then all information and phone settings will be lost forever.

Method 3 - DFU

DFU stands for Device Firmware Update and is the deepest recovery mode available for iPhones or any iOS device. It will completely destroy the information on your iPhone, but after that it will work as if it were just out of the box. The device will stop freezing, will work faster and crashes or errors in applications will disappear.

The first step is to launch iTunes and connect your phone. For iPhone 6S, hold down the "Sleep/Wake" and "Home" buttons at the same time for about 8 seconds. For 7k and newer, also hold these buttons together with "Volume Down" for 8 seconds. After 8 seconds, release the "Sleep" button, but keep holding the "Home" or "Volume Down" buttons, depending on the model. Your iPhone screen will be dark for a while and then the device will enter DFU mode. Release all buttons and select Restore iPhone. This solution is used by professionals and it helps when iphone stuck on itunes as well as in other situations.

Method 4 – Tenorshare Reiboot

In some cases, the so-called Recovery Loop occurs, i.e. "recovery loop". This means that after any of the above methods of recovery, the phone will continue to display a black screen and the very hated iTunes and cable icon to no avail. The reason lies in the misses of updating the operating system or in the errors of restoring the iOS firmware.

Fortunately, there is a large selection of effective programs to treat this problem. To fix this using the utility, you need to perform a few easy manipulations in a couple of clicks. Now the question is “iPhone stuck on iTunes, what should I do?” won't seem so intimidating.

Connect your iPhone and go to the utility. Then select the free function "Exit Recovery Mode".

If it still does not solve your problem, then select the "Fix operating system (resolve all iOS freezes)" option and click "Start".

A recovery window will appear in front of you, on which you should select "Fix Now". Reiboot will start downloading the firmware package and after the download is complete, click "Start OS Recovery".

This process may take a little time, but it will help to revive your device if the iphone is stuck in recovery mode and get rid of this problem.

Friends, occurrences USB cord and iTunes icon on the screen of iPhones, iPads and iPods are quite common. In general, it is generally accepted that if a cord and an icon in the form of the iTunes logo appear on the black display of one of these devices, then this means that Recovery Mode is running. But not everyone knows that the cable and iTunes, in addition to Recovery Mode, can mean Recovery Loop, which is different from recovery mode.

In order for you to be able to make an accurate diagnosis, to determine the mode in which your iPhone (or other device) is located, displaying the USB wire and iTunes, we will describe the results of our research acquired as a result of the operation of these mobile Apple devices. And maybe even our meager knowledge will help someone solve their problem and restore the phone or tablet.

Recovery mode - normal

The iPhone or iPad is entered into the normal recovery mode using simple steps, the sequence of these actions is described here - "". To exit the usual Recovery Mode, we simply left the iPhone for a while, it rebooted itself and exited the recovery mode. For an immediate exit from recovery mode (what would not wait) we simply force . It turns out that, unlike the others, it is quite easy to exit the normal recovery mode by rebooting.

Recovery Loop Mode - Obedient

There are cases that after a forced reboot, which is used to exit the normal recovery mode, the iPhone still continues to load a black screen on which we see the cord and iTunes again and again. This situation means that the iPhone is in the so-called Recovery Loop mode. A phone or tablet is very often driven into this mode by iTunes. Getting into the Recovery Loop can occur for various reasons, for example, as a result of or restoring the iOS firmware. The recovery loop can occur as a result of a software, hardware or domestic failure (for example, accidentally pulled out the cable), once we ourselveswhen we tried to downgrade the iOS firmware version from 7 to 6th.

Why did we add the word "Obediant" in the subtitle? Yes, because it is still possible to exit the obedient recovery loop and return the iPhone to a working state without losing information, for this we used, some users with TinyUmbrella had difficulties, and we found a more convenient way to exit Recovery Loop using the program. There are other programs for getting out of the loop - iReb and RecBoot.

Recovery loop mode - not docile

If your iPhone or iPad gets into a naughty Recovery Loop, then, as a rule, not only a forced reboot is powerless, but the redsn0w, iReb, TinyUmbrella and RecBoot programs also cannot get the iPhone out of the recovery loop. As a result of applying the programs above, the iPhone continues to show the USB cable and the iTunes logo after rebooting. In this case, we did not succeed in avoiding the loss of information stored in the iPhone, but it’s good if you did too before.

If you caught a naughty recovery loop, then all that remains is to connect the iPhone to iTuens and try to flash it. Sometimes it is not possible to flash the phone in this mode, then they try to flash it again. As a result of the firmware, the iPhone erases all the information we made earlier. It happens that after flashing an iPhone or iPad, they are asked to enter someone's Apple ID and password, but that's a completely different story.

How is the repair going:

• 1 Free diagnosing brought-
  device, either by you or our courier.
• 2 We make repairs, and also give a guarantee on new installed parts. On average, repairs last 20-30 minutes.
• 3 Get a working device yourself or call our courier.

However, there is a somewhat different from the "Recovery Mode" or recovery mode, the "loop" mode or otherwise "Recovery Loop". How to accurately diagnose and what to do to restore the iPhone 6 Plus to working capacity?

A normal recovery boot can be stopped with a forced reboot, or simply wait for the process to complete. But if the iPhone 6 Plus freezes, it means that it has moved into the Recovery Loop.

Loop mode means that the Apple device is “hanging” and cannot return to a working state on its own, or during diagnostics, a system error or hardware failure has occurred that cannot be resolved by a forced reboot.

Moreover, a system freeze may occur, including after a forced reboot.

Why iPhone stuck on iTunes cord

Reasons that lead to the "loop":

• Trying to downgrade the modem through iTunes;
• IPhone 6 Plus system update download interruption;
• Attempt to downgrade the firmware version through the computer;

How to restore work if the iPhone is frozen?

Getting out of the Recovery Loop is much more difficult. You can try to boot the device using special applications. For these purposes, the most commonly used programs are TinyUmbrella and RedSn0w.

There are two kinds of "loop": obedient and naughty.

In the first case, it is difficult to return the iPhone 6 Plus to working capacity without data loss, but it is possible. To do this, you should use the TinyUmbrella program, there are other programs, but to work with this software, in any case, you need at least basic knowledge and understanding of the processes that will occur.

We serve employees of these companies

We do a flashing if the iPhone 6 hangs on a cord, with high quality!

If the iPhone 6 Plus freezes and gets into a naughty Recovery Loop, then any attempts to rehabilitate the phone are already powerless.

The only way out is to reflash the device.

In the event that it is not possible to install a new version of iOS on an iPhone via iTunes in the usual mode, and the phone continues to “hang”, a special emergency DFU mode is introduced. In this case, you lose all the information that you stored on your smartphone, but you can recreate it after flashing it from a backup.

iPhone stuck on iTunes cord

If there is no way to do it yourself, then only qualified craftsmen should entrust the firmware of the gadget 6 Plus. Everyone should understand why experience and professionalism are important here. We have been working in this area since 2009, the accumulated experience allows our specialists to quickly and efficiently restore the system, change the speaker, and other failed parts and return your phone to a fully working condition.

Lately, I've been seeing more and more complaints about unsuccessful iPhone updates using iTunes. Often, such an update leads to a complete crash of the firmware and the inoperability of the phone. The victims have no choice but to take their phone and wallet in their arms and go to the nearest service center, where, for a very decent amount, a specialist with a very thoughtful look will carry out “very difficult” work to restore the iPhone firmware. At the same time, not many people know that thanks to the foresight of Apple developers, firmware recovery can be done at home and this procedure will take quite a bit of time.

The firmware on the iPhone or “apple, usb cable and iTunes icon” has flown.

There are three main signs that the firmware on your phone has crashed or is damaged:
1. The iPhone does not turn on and on the screen you see (oddly enough) only a black screen.
2. The phone can be turned on, but the screen shows only the Apple logo and does not respond to anything.
3. The phone turns on, but the screen shows the USB cable and the iTunes icon.

Before proceeding, carefully inspect your phone. Perhaps the malfunction is caused by physical damage to the device, in which case the firmware will not help you. If your pet looks great, and there are no holes from enemy bullets in it, you can connect it to your computer using a USB cable.

ATTENTION! Make sure you have the latest version of iTunes installed on your computer. .

After connecting the cord, you need to simultaneously hold down the "Power" and "Home" buttons for 10 seconds. After 10 seconds, release the Power button, but keep holding the Home button.

Your computer should start detecting the phone, which in turn means the phone is alive and needs to be rebuilt.

iPhone Firmware Recovery

Before starting the firmware procedure, you must wait until the phone is completely detected by the computer. After that, you need to launch iTunes, which in turn will swear that the phone is in recovery mode.

You only need to click the "Restore" button and agree to the terms.

After that, it remains to wait until the firmware is downloaded to the iPhone and the process of its restoration is completed, however, iTunes will periodically notify you about this. In addition, the progress of the firmware will be shown on the phone screen.

After completing the firmware, your phone will automatically turn on. After that, you need to go to "Settings" -\u003e "General" -\u003e "Reset" -\u003e "Reset all settings".

It is worth adding that if you are the proud owner of an unofficially unlocked phone, then with a high degree of probability you can receive the following message:

Unfortunately, the tricks up the sleeve ran out on this, and the iPhone 4/4S with modems 4.12.01/2.0.12, in principle, cannot be unlocked programmatically. It remains to either contact the operator for an official unlock, or use the Gevey Sim kit, but that's a completely different story.