Error numbers when connecting to the Internet. Errors when connecting a VPN connection

Hello friends! Do you have error 651 when connecting to the Internet and you do not know how to fix it? In this article I will tell you in detail what I know about it and how I fix it. By the way, my name is Zhenya, and with any questions, you can contact this article in the comments. Ask all questions there or in the section (contacts). Well, let's get started?

Just recently, my friend called me and asked me to fix this error, I still didn’t know how to do it, but after climbing the Internet, I found the answer and I’m sharing it with you.

Error 651 when connecting to the Internet

Let's look at a few options to fix this problem. But first, watch the video, it also has the answer.

1. From the very beginning, you can call your ISP and report this error. It may be that they created this error 651 when connecting to the Internet and they will fix it as soon as possible. But as we all know, basically the operators there themselves do not know anything, and all they can advise is to restart the computer and see what happens. But that doesn't work for us, does it?
2. If the operator did not help you, then you can simply delete your Internet connection and create it again. Think you know how to do it? If not, write about it in the comments, and I will answer you by mail.
3. Sometimes I was helped by such an option as reinstalling the drivers for the network card.
4. If you have an ADSL router or Wi-Fi installed in your house, then I advise you to read the article, but this is after you fix error 651.
5. You can still restore checkpoint, that is, roll back the operating system a week or a couple of days ago. I'm sure you know how to do it.
6. Well, let's move on to the most real solution to this error, so repeat after me. Click on the start button> run> and enter the regedit command there after that we will need to dig a little in the registry, do not be afraid, this is not scary. This is how I will write now, and go through the registry branches HKEY_LOCAL_MACHINE \ SYSTEM \ CurrentControlSet \ Services \ Tcpip \ Parameters as soon as you get to the last branch of the section ( Parameters ) create a DWORD parameter there and point to the name EnableRSS also do not forget to specify the value ( 0-zero). OK! Let's move on, now we need to create another DisableTaskOffload parameter with a value of (1-one). And after performing all these operations, you can safely restart your computer and everything will work.

I really hope that the article error 651 when connecting to the Internet helped you. Well, as I said earlier, you can ask any questions that you have left in the comments, and I will definitely answer you!

If an error occurs when starting the VPN connection, then you need to remember or write down its three-digit code.

As a rule, errors have the code:

6XX (errors associated with incorrect password entry, name or communication protocol type selection and indicate that the network is working, but you need to check the input data);

7XX (errors related to incorrect connection settings and indicate that the network is working, but you need to check the settings);

8XX (errors related to network setup problems or lack of network connectivity. If you encounter this series of errors, contact support).

Error: 600, 601, 603, 606, 607, 610, 613, 614, 616, 618, 632, 635, 637, 638, 645

Description:
An internal Windows error has occurred.

Elimination method:
Restart your computer.
If the error persists, check your computer for viruses.
Delete Recently installed programs, or undo recent changes in Windows settings if there were any.

Error: 604, 605, 608, 609, 615, 620

Description:
Remote Subsystem Phonebook File Windows Access and the current Dial-Up Networking configuration are not compatible with each other.

Elimination method:
Restart your computer. If the error persists, then delete and re-create the VPN connection.

Error: 611

Description:

Elimination method:
Restart your computer and make sure that the local network is functioning properly on your computer.
If the error does not disappear, then contact the technical service. support.

Error: 612

Description:
Internal configuration Windows networks configured incorrectly.

Elimination method:
Similar to error 611.
In addition, the error may be caused by a lack of resources (memory) on your computer.
Try closing running programs.

Error: 617

Description:
Windows is in the process of connecting to the Internet, or an internal Windows error has occurred.

Elimination method:
Wait a few minutes.
If the connection is not established, and when reconnecting, the error repeats, then restart the computer.

Error: 619

Description:
The security settings of the VPN connection are configured incorrectly, VPN traffic is blocked on the way to the gateway, or VPN settings did not take effect.

Elimination method:
In the properties of the VPN connection, open the "Security" tab - "Normal (recommended settings)" should be selected and the "Data encryption is required (otherwise disconnect)" checkbox should be unchecked.
Restart your computer and try connecting again.
Check your firewall settings, and if you are not sure if they are correct, disable it.
If your computer does not receive responses when pinging, then there is a problem with the network and you should report the problem to the support team.

Error: 624

Description:
Prohibition to create a connection.

Elimination method:
There is no Rasphone.pbk file in (Windows folder)/system32/RAS or … Documents and Settings/(your user or all users)/Application Data/Microsoft/Network/Connections/Pbk, and even if it exists, rename it to something else like RASPHONE.OLD, you can also run rasphone.exe, might help.
There is a ban on creating a connection.
Allow users to create new connections.
"Start" - "Run" - gpedit.msc and sort it out there.
Folder access denied
Documents and Settings/All Users/Application Data/Microsoft/Network/Connections/Pbk - Share the folder.
But most likely the problem can be solved in this way: uncheck the "Read only" item in the properties of the Rasphone.pbk file.

Error: 629

Description:
The VPN connection was terminated for a reason Bad quality communication or after unsuccessful negotiation.

Elimination method:

Error: 633

Description:
The modem is already in use or is not configured for outgoing calls.

Elimination method:
The VPN device to be used by the network cannot be opened.
Contact the service technical support.

Error: 635

Description:
An error has occurred in Windows.

Elimination method:
Try to re-establish the VPN connection, or Windows entirely.
If nothing helps, contact technical support.

Error: 642

Description:
Your computer has been assigned a NetBIOS name that is already in use on the network.

Elimination method:
Change the computer name in the properties of "My Computer" in the "Identification" section.

Error: 650

Description:

Elimination method:
The Internet access server is unavailable.
Check if "Connect by local network", whether the network card is working, whether the network cable, whether a specific IP address is set in the IP connection settings.
Check your settings network adapter and make sure that the local network is working for you.
If you checked everything, but found no errors, call technical support.

Error: 651

Description:
The VPN server is not responding to requests.

As a rule, an error occurs when a software or hardware failure of network equipment occurs - for example, a computer network card, router, or modem.
In Windows 7, unlike Win XP or Vista, the number of reasons is much greater - from an unconnected network cable to a mismatch in the raspppoe.sys file and encoding differences.
If the provider's technical support service cannot help, you will have to solve the problem yourself.

Elimination method:
Restart your computer.
Set up your internet connection again.
Reinstall or update the drivers for the network card.
Check the operation of the ADSL modem, if it is used, of course.
Reinstall the Windows operating system or roll back to an earlier state.

Additionally, check if the VPN server address is correct.
Check all connections, sockets and patch cords (cables) with a special tester.

The problem sometimes occurs if Windows 2003 is used - it manifests itself in the fact that when manually specifying the PPTP protocol, error 651 occurs, and when automatic detection error 800.
It is possible to cope with the problem by making small adjustments to the parameters in the registry.
Need to disable Receive side Scaling and Offloading support.
To do this, run Regedit (Start - Run - enter the command regedit).
Next, we go through the branches of the registry
HKEY_LOCAL_MACHINE\ SYSTEM\ CurrentControlSet\ Services\ Tcpip\ Parameters there we create a DWORD parameter and name it EnableRSS, assign it a value of zero (0).
Next, you should find the registry branch
HKEY_LOCAL_MACHINE\ SYSTEM\ CurrentControlSet\ Services\ Tcpip\ Parameters and create the DisableTaskOffload parameter in it with a value of 1.
If the parameter exists, just change the value by one.
After the done operations, it is worth restarting the computer.

Error: 678

Description:
No response from VPN server.

Elimination method:
This type of error occurs when there is no connection between your computer and the access server.
Most likely the cause of this error is: malfunctions on the active equipment, the client's network card is disabled, the connection is blocked by an antivirus program or firewall.
Check if your local network is working.
Check your VPN connection settings and your firewall settings if it is installed on your computer.
If all else fails, then contact technical support.

Error: 691

Description:
The username or password was entered incorrectly, or the funds on the account ran out.

Elimination method:
No money.
Incorrect login or password.
The VPN server is incorrectly specified in the settings.
There is a user or administrative block in the statistics system.
Make sure that when entering your login and password, the " cap lock» on the keyboard is turned off and the English layout is set.
If you are sure that you are entering your login and password correctly, and you have funds on your account, then contact the technical support service of our network.
Most often, this error occurs for users if they really do not type “Username” and “Password” correctly, or if you have already connected to the network under your login.

Error: 720

Description:
The error indicates that the registry keys that store the Winsock configuration are corrupted.

* netsh int ip reset resetlog.txt
* netsh winsock reset

After that, we restart the computer and set up a local network connection, since executing this command overwrites the registry settings that are used by the TCP / IP protocol stack, which is tantamount to deleting and reinstalling it.
Re-create the VPN connection if necessary.
Warning!
Running the netsh winsock reset command can adversely affect programs that access the Internet or monitor data on the Internet: antivirus programs, firewalls and proxy clients.
When incorrect operation one of these programs, after using the method in question, reinstall the program to restore its functionality.

Error: 721

Description:
The remote computer is not responding.

Elimination method:
- Check if the correct VPN server is registered in the VPN connection.
To do this, go to "Start" - "Control Panel" - "Network Connections".
Right-click on the shortcut for your VPN connection and select Properties.
General tab - The Computer name or Destination IP address line must contain the address of the VPN server.
- In most cases, error 721 occurs due to the fact that a firewall (firewall) is installed on your computer.
This program, if configured incorrectly, can block network traffic.
To be 100% sure, disable all firewalls (Outpost Firewall, Zone Alarm, Kaspersky Internet Security ...) including the Windows Firewall ("Start" - "Control Panel" - "Windows Firewall").
Try to connect.
If the error is gone, try configuring your firewall correctly.

Error: 734

Description:
The PPP link control protocol has been terminated.

Elimination method:
This error can occur if the security protocols on the server to which you are connecting are incompatible with the local security settings.
In the Network Connections folder, right-click the connection you are using.
Select the "Properties" command and open the "Security" tab.
In the list when checking uses, select "Insecure password".

Error: 735

Description:
The requested address was rejected by the server.

Elimination method:
You have configured the VPN connection incorrectly to access the Internet.
Most likely, in the TCP / IP settings of the VPN connection, you registered some kind of IP address, and it should be allocated automatically.
Make sure that the network settings (or rather, the TCP / IP protocol settings) of the VPN connection do not specify a specific IP address, and all parameters are obtained automatically.

Error: 741, 742, 743

Description:
Encryption settings are incorrectly configured.

Elimination method:
Go to the VPN connection settings, and in the "Security" tab, disable the "data encryption" item.

Error: 769

Description:
The specified destination is unreachable.

Elimination method:
The reason for this error is that the network card on your computer is disabled.

Error: 789

Description:
Invalid VPN connection type selected.

Elimination method:
Go to the VPN connection settings and on the "Network" tab, from the "VPN Type" list, select "PPTP VPN".
Try reconnecting.

Error: 797

Description:
A name already in use is listed in the computer settings.

Elimination method:
Change computer name.

Error: 800

Description:
No access to VPN server.

Elimination method:
It is recommended to check whether there is a physical connection (whether the lights on the network card on the back of your computer are on), whether the network cable is plugged into the connector on network map and outlet (if available).
Then check if LAN connection is enabled.
To do this, click the "Start" button, then "Control Panel", then "Network Connections".
In the window that appears, find "Local Area Connection" and turn it on if it was turned off.
Try pinging your local gateway.
To do this, click the "Start" button, then "Run".
In the line that appears, type in English layout cmd, click OK.
In the black window that appears in the English layout, type: ping XX.XX.XX.XX (XX.XX.XX.XX must be replaced with the address of your gateway.
The gateway address can also be viewed in the properties network connection TCP/IP) press "Enter" on the keyboard.
If the message "Request timeout exceeded" appears in the black window five times or more, then call the technical support of your Internet provider.

New GeForce Driver Pack 387.92 (WHQL)

Nvidia prepared new version GeForce driver and software package with index 387.92 and Microsoft WHQL certification.
The new release is Game Ready and aims to provide the best performance in Middle-earth: Shadow of War, The Evil Within 2, Forza Motorsport 7, and Arktika.1 VR project.

Other new features of the GeForce 387.92 WHQL release include support for Fast Sync technology on SLI bundles from Maxwell and Pascal generation graphics cards, OpenGL graphics API version 4.6, and support for HDR (high dynamic range) with Nvidia GameStream on PCs with operating system Windows 10.

In addition, SLI profiles have been added/updated in the latest release for the following games: Earthfall, Lawbreakers, Middle-earth: Shadow of War, Nex Machina, ReCore, RiME, Snake Pass, Tekken 7, The Evil Within 2 and We Happy Few.

1.65 million hacked home computers are mining

Kaspersky Lab published the results of its study, according to which there are 1.65 million hacked PCs in the world that are busy mining cryptocurrency for hackers.
It is noted that we are not talking only about home machines, but also about corporate servers.

The laboratory noted that the most popular malicious currency miners are Zcash and Monero.
The most popular currency is Bitcoin, but its mining is too inefficient for conventional computers, as opposed to alternative currencies.

“The main effect for home computers or the infrastructure of an organization is a decrease in performance,” said Kaspersky security expert Anton Ivanov, “Also, some miners can download modules from the infrastructure of a dangerous action, and these modules may contain other malicious code, such as trojans.”

In most cases, the miner enters the computer with the help of a specially created malicious program, the so-called dropper, whose main function is to covertly install other software.
Such programs are usually disguised as pirated versions of licensed products or as activation key generators for them - users look for something like this, for example, on file sharing services and deliberately download it. But sometimes what they download is not exactly what they wanted to download.

After launching the downloaded file, the installer itself is installed on the victim’s computer, and he is already uploading the miner to the disk and special utility, masking it in the system.
Also, the program can be bundled with services that provide its autorun and configure its operation.

From malware droppers Kaspersky Internet Security will protect you by default - just make sure that the antivirus is always enabled, and such malware simply will not get on your computer.

But miners, unlike droppers, are not malicious programs.
That is why they are included in the category riskware- Software that is legal in itself, but can be used for malicious purposes.
By default, Kaspersky Internet Security does not block or remove such applications, as the user may have installed them deliberately.

But if you want to play it safe and are sure that you are not going to use miners and other software that is included in the Riskware category, then you can always go to the settings of the security solution, find the section Threats and detection and check the box next to Other programs.

If you're busy mining for someone else, you can end up with huge electricity bills, noticeable PC slowdowns, and high component temperatures.

Processor socket LGA 1151 for Intel Coffee Lake has differences

The release of Intel Coffee Lake processors caused a storm of emotions among users and a flurry of discussions on various thematic resources, mainly due to the fact that they will only work with new motherboards, despite the long-used LGA 1151 design.

The real cause of the incompatibility has been found out.
The thing is that the contacts on the new Intel processors are arranged in a different way than the Skylake and Kaby Lake processors, VideoCardz reports.

Intel has added more Vss (ground) and Vcc (power) pins to the new processors.
The first ones were 377 before, and now there are 391.
The second - 128 and 146, respectively.
The total number of contacts has not changed, and remains equal to 1151, and all thanks to a decrease in the number backup contacts(RSVD) from 46 to 25.

The company said that the eighth generation Core processors needed additional and / or more stable power supply.
Although it was enough for the company to change the name to LGA 1151v2 to avoid the "righteous anger" from some users, it did not.

Wi-Fi hotspots in rural areas

Rostelecom reports a sharp increase in the demand for wireless Internet access points built as part of a project to bridge the digital divide in Russia.

The project in question involves the creation of Wi-Fi points in settlements with a population of 250 to 500 people.
Network access is provided at a speed of at least 10 Mbps.

At the end of July, Rostelecom announced the abolition of fees for connecting to the Internet through such hot spots.
Immediately after that, the demand for the service increased markedly.
The number of Internet sessions at hotspots jumped by 35%.
The total amount of Internet traffic in Wi-Fi points in August for the first time exceeded 1 PB, being 27% more than a month earlier.

As of June 30, 2017, universal communication services using Wi-Fi access points were provided in 4690 settlements, which is 34% of the total plan (almost 14 thousand points should be built by the end of 2019).
35,000 kilometers of fiber-optic communication lines have already been laid.

If you have problems with the Internet, you can try to deal with them yourself. This will save you time and hassle if you are trying to emergency assistance from the provider.

If the connection fails, an error code is indicated. To deal with the problem and he's the one you'll need. H Below we list the most common errors and attach instructions for action.

The first thing to do before diagnosing is to connect the Internet cable directly to the computer's network card. Those. remove the cable from the router or router and connect to the appropriate connector on a computer or laptop.

Error code 54
What's happened? Unable to connect to the network due to a name match.

What to do? Set the automatic receipt of the ip-address.
V Windows XP From the Start menu, select Settings, then Control Panel. Next, "Network Connections", right-click on "Local Area Connections" and open "Properties". Select "Internet Protocol", select "Properties" again and left-click on the item "Obtain an ip-address automatically".
Windows 7. "Start" - "Control Panel" - "Network and Sharing Center" - "Change adapter settings". In the "Network Connections" window, right-click on "Local Area Connections", "Properties". In the window that appears, select "Internet Protocol", again go to "Properties" and with the left mouse button make the item "Obtain an ip-address automatically" active.

Error code 600, 601, 603, 606, 607, 610, 613, 614, 616, 618, 632, 635, 637, 638, 645
What's happened? An internal error in the Windows operating system.

What to do? Reboot the system. If the error persists, try scanning your computer for viruses. Check recently installed programs, changes in settings, you may have to uninstall or restore the system. If the above steps don't work, please contact support.

Error code 619
What's happened? Incorrect security settings or VPN connection settings did not take effect, or traffic is blocked on the way to the gateway.

What to do? Open the "Properties" of the VPN connection and select the "Security" section. Check the "General Settings" icon and, if so, uncheck "Requires data encryption". Then restart Windows and try to connect to the network. If the error persists, check the PPPoE connection settings.

Error code 642

What's happened? Your computer name is already in use.

What to do? Open "My Computer" by right-clicking "Properties", go to the "Computer Name" tab, in the "Identification" section, change the name to any other.

Error code 678, 718

What's happened? No response from VPN (PPPoE) server.

What to do? Check the operation of the local network and VPN connection settings, as well as firewall settings(if installed). If the problem persists, please contact support.

Error code 691

What's happened? The username or password is invalid in this domain, or the computer cannot establish a remote network connection.

What to do? First, check if you entered the password correctly and try to reconnect. Please note that the input language must be English and all cases (the difference between uppercase and lowercase characters) are correct.

Error code 741, 742, 743, 789

What's happened? The remote computer does not support the required type of data encryption.

What to do? Check PPPoE connection settings. To do this, go to the VPN connection settings, disable "data encryption". In the "Network" tab, in the "VPN type" list, select "PPTP VPN" and try to connect again.

Error code 769

What's happened? The network card is off.

What to do? In Device Manager ("Start" - "My Computer" - "Properties" - "Hardware" - "Device Manager") enable the network adapter. In "Network Connections", set "Local Area Connection". If the error persists, check your computer for viruses. If the problem persists, contact technical support.

Error code 651, 678, 718, 800, 868

What's happened? There is no connection to the server.

What to do? First, check if the local network is working. If yes, then try resetting PPPoE connection if you have a VPN connection. Restart the DNS client ("Start" - "Control Panel" (for XP) or "System and Security" (for Vista and 7) - "Administrative Tools" - "Services"). If it doesn't work, you know where to turn ;)

"Network cable not connected"

What to do? Try reconnecting the cable, reboot the network card (See error code 769). If you have another computer / laptop, then try connecting the cable to it and see if the connection is established. If the result is negative, contact technical support.

If the VPN connection cannot be established, the system displays an error number with a brief explanation in a pop-up window.

To facilitate the search and correction of VPN connection errors, I provide a list of all, incl. and the most common errors that can occur with connection problems, and recommendations for correcting them. I want to warn you right away, do not be alarmed if you come across in the error descriptions mentions of modems, dial numbers and other crap that is not used in FTTB technology, these standard errors have not changed since the time of King Pea. You yourself will most likely encounter errors 712, 769, 619, 691, 800, 868.

VPN connection errors.

If an error occurs when starting the VPN connection, then you need to remember its three-digit code. As a rule, errors have the code

1. 6XX (errors associated with incorrect password entry, name or communication protocol type selection) - indicate that the network is working, but you need to check the entered data,
2. 7XX (errors related to incorrect connection settings) - indicate that the network is working, but you need to check the VPN connection settings
3. 8XX (errors related to network setup problems or lack of network connectivity). In the event of errors in this series, please contact the support service at tel. 35-000-35).

Below are the decryption codes:

Error 600 A started operation has not been completed.

Error 601 An invalid port descriptor was encountered.
Recommendation: An internal error has occurred. Reboot your computer to ensure that any recent configuration changes have taken effect.

Error 602 The specified port is already open.
Recommendation: COM port to be used network connection, is already in use by another active network connection or process (for example, a monitoring program telephone line such as a fax program). Quit the application blocking the COM port

Error 603 The caller's buffer is too small.
Recommendation: An internal error has occurred. Reboot your computer to ensure that any recent configuration changes have taken effect.

Error 604 Invalid information provided.
Recommendation: The dial-up phone book file and the current Dial-Up Networking configuration may not be compatible. If you have replaced your communications hardware (serial port or modem), check your Dial-Up Networking configuration.

Error 605 Unable to set port information.

Error 606 The specified port is not connected.
Recommendation: An internal error has occurred. Reboot your computer to ensure that any recent configuration changes have taken effect.

Error 607 An invalid event was encountered.
Recommendation: An internal error has occurred. Reboot your computer to ensure that any recent configuration changes have taken effect.

Error 608 A non-existent device was specified.
Recommendation: The dial-up phone book file and the current Dial-Up Networking configuration may not be compatible. If you have replaced your communications hardware (serial port or modem), check your Dial-Up Networking configuration. If this error continues to occur, delete and recreate remote connection to the network.

Error 609 The specified device type does not exist.
Recommendation: The dial-up phone book file and the current Dial-Up Networking configuration may not be compatible. If you have replaced your communications hardware (serial port or modem), check your Dial-Up Networking configuration. If this error continues to occur, remove and re-create the remote network connection.

Error 610 An invalid buffer was specified.
Recommendation: An internal error has occurred. Reboot your computer to ensure that any recent configuration changes have taken effect.

Error 611 The specified route is not available.

Error 612 The specified route is not distributed.
Recommendation: The network configuration is probably incorrect. Reboot your computer to ensure that any recent configuration changes have taken effect. This error can also happen if your computer is running out of working resources.

Error 613 Invalid compression type specified.
Recommendation: An internal error has occurred. Reboot your computer to ensure that any recent configuration changes have taken effect.

Error 614 Not enough available buffers.
Recommendation: An internal error has occurred. Reboot your computer to ensure that any recent configuration changes have taken effect.

Error 615 The specified port was not found.
Recommendation: The dial-up phone book file and the current Dial-Up Networking configuration may not be compatible. If you have replaced your communications hardware (serial port or modem), check your Dial-Up Networking configuration. If this error continues to occur, remove and re-create the remote network connection.

Error 616 Asynchronous request suspended.
Recommendation: An internal error has occurred. Reboot your computer to ensure that any recent configuration changes have taken effect.

Error 618 The specified port is not open.
Recommendation: An internal error has occurred. Reboot your computer to ensure that any recent configuration changes have taken effect.

Error 619 The specified port is not connected.
Recommendation: Reboot your computer to ensure that any recent configuration changes have taken effect. If the error has not been resolved, disable security programs (antiviruses, firewalls).

Error 620 Failed to determine endpoints.
Recommendation: The network configuration is probably incorrect. Reboot your computer to ensure that any recent configuration changes have taken effect.

Error 621 The system was unable to open the phonebook file.

Error 622 The system was unable to load the phonebook file.
Recommendation: Dial-Up Networking uses the Rasphone.pbk file located in the \System32\Ras directory. Make sure the file is in this directory, then restart Dial-Up Networking.

Error 623 The system could not find a phone book entry for this connection.
Recommendation: Dial-up Web Access has found the phone book, but cannot find an entry for this connection. This error will not occur unless another application is using the Dial-up Web Access phonebook and specifies an invalid connection entry.

Error 624 The system was unable to update the phonebook file.
Recommendation: Dial-Up Networking uses the Rasphone.pbk file located in the \System32\Ras directory. Make sure your disk is not full and you have permission to modify this file.

Error 625 The system encountered invalid data in the phonebook file.
Recommendation: The phonebook file Rasphone.pbk may be corrupted. Delete this file from the \System32\Ras directory, then restart Dial-Up Networking in order to create a new phone book.

Error 626 Failed to load row.
Recommendation: An internal error has occurred. Reboot your computer to ensure that any recent configuration changes have taken effect.

Error 627 The key could not be found.
Recommendation: One of the Dial-Up Networking configuration files may contain incorrect information. If you are using a modem not supported by your Windows version, install a supported modem.

Error 628 The connection was closed.
Recommendation: If this is a dial-up connection, try calling back. If you continue to receive this message, lower your modem's initial speed and disable additional settings modem. If this problem continues to occur, contact your system administrator. If it is a virtual private network (VPN) connection, access may be denied due to remote access policy or other reasons. Contact your system administrator.

Error 629 The connection was closed by the remote computer.

Unrecoverable line error.
Noise on the line.
Disabled by the system administrator.

You can try connecting to a different server to see if the issue is specific to the server you are trying to reach. Also, you can try to connect to your server from another PC.

Error 630 The modem was disabled due to a hardware error.
Recommendation: Connection terminated due to one of the following reasons:
An unrecoverable error has occurred in your modem (or other communication equipment).
An unrecoverable error has occurred on your communication port.
Your modem cable is disconnected.
To diagnose and solve the problem, do the following:
Make sure your modem is turned on and the cable is securely connected.
Make sure your modem is functioning properly.

Error 631 The user has disconnected the modem.
Recommendation: Due to an event on your computer, the connection was terminated. Call back.

Error 632 Incorrect structure size detected.
Recommendation: An internal error has occurred. Reboot your computer to ensure that any recent configuration changes have taken effect.

Error 633 The modem is already in use or is not configured for outbound dial-up connections.
Recommendation: If this is a dial-up connection, the COM port to be used by the network connection is already in use by another active network connection or process (for example, a telephone line monitoring program such as a fax program). Quit the application blocking the COM port. If it is a virtual private network (VPN) connection, the VPN device to be used by the network cannot be opened. Check for a Local Area Connection icon (LocalAreaConnection) in the Network Connections folder (Network connections). If the icon is missing, the problem may be the lack of network card drivers or the network card itself. Restart your computer and update your network card drivers. If you see the "Local Area Connection" icon (Local Area Connection), then after rebooting the computer, create the VPN connection again.

Error 634 Failed to register the computer on the remote network.
Recommendation: The remote access server cannot register your computer name on the network. This is more likely to happen with the NetBIOS protocol, however, it can also happen with the TCP/IP or IPX protocols. This usually happens if the address is already in use on the network. Contact your system administrator.

Error 635 An unknown error has occurred.
Recommendation: An internal error has occurred. Reboot your computer to ensure that any recent configuration changes have taken effect.

Error 636 The device connected to the port is not what you expect.
Recommendation: Your hardware configuration and the configuration settings for your connection may not be compatible with each other. If you have replaced your communications hardware (serial port or modem), check your Dial-Up Networking configuration.

Error 637 A string was found that could not be converted (converted).
Recommendation: An internal error has occurred. Reboot your computer to ensure that any recent configuration changes have taken effect.

Error 639 No asynchronous network available.
Recommendation: Your NetBIOS network may be misconfigured. Reboot your computer to ensure that any recent configuration changes have taken effect.

Error 640 An error has occurred that affects NetBIOS.
Recommendation: The modem cannot establish a connection at the specified speed. Lower the initial speed of the modem and call back. Also, try disabling hardware and software compression. If the connection still fails, try adding NWLink IPX/SPX/NetBIOS Compatible Transport Protocol.

Error 641 The server was unable to allocate the NetBIOS resources required to support this client.
Recommendation: Ask your system administrator to increase the resource capacity of the remote access server, or use Services in Computer Management to stop non-essential services on your computer such as Messenger and Network DDE.

Error 642 One of the computer NetBIOS names is already registered on the remote network.
Recommendation: Another computer with the same name is already connected to the remote network. Each computer on this network must be registered with a unique baud name. Check the following:
Is there a computer with the same name as yours on the network you are connecting to.
Whether your computer is physically connected to the network you are trying to connect to.

Error 643 Server network adapter error.
Recommendation: Report the bug to your system administrator.

Error 644 Pop-up network messages will not be received.
Recommendation: Another computer already connected to this network uses your name to receive network messages. Messages addressed to you are sent to this computer. If you want to receive messages on your remote workstation, you must log out of your office computer before you dial the network next time. This error does not affect Microsoft Outlook, Microsoft Outlook Express, or Microsoft Exchange messages.

Error 645 An internal authentication error has occurred.
Recommendation: An internal error has occurred. Reboot your computer to ensure that any recent configuration changes have taken effect.

Error 646 Login at this time of day for the user with this account is not allowed.
Recommendation: Your account is configured for time-of-day network access. If you need to log on to the network during a day other than the one configured on this moment, ask your system administrator to change the configuration.

Error 647 The account is disabled.
Recommendation: User account is disabled. This could be due to multiple repeated failed connection attempts, or because the system administrator disabled the account for security reasons (or for non-payment). Ask your system administrator to enable your account.

Error 648 Password expiration date for account expired.
Recommendation: You need to change your password.
If you are connecting via Dial-Up Networking, you will automatically be prompted to change your password. If you are connecting using the rasdial command, you can change the password by doing the following:
Press CTRL+ALT+DEL.
Click "Change Password" and then follow the instructions that appear on the screen.
If you belong to the Administrators group and your password has expired, another administrator must change your password. You will not be able to change your password yourself.

Error 649 The account does not have rights to dial.
Recommendation: The account does not have access rights to the server for one of the following reasons:
Your account on the selected server is valid, but you do not have dial-up access to the network. Ask your system administrator to set the remote access permission for your account, or set the permission in Routing and Remote Access.
Your account has expired and the account has been disabled, or your remote access has been terminated.
You are trying to connect to the server outside the allowed time of day, the number of connection attempts has exceeded the maximum allowed, or your account may not allow remote login.
Your account settings may be preventing connections. For example, your account may only allow connections from certain phone numbers. The remote computer can only allow connections to local accounts.
Your computer may not support the requested authentication protocol, or your computer may be trying to use a protocol that the remote computer does not accept.
If you have an account with remote access rights on another domain, follow the steps below to use your account on that domain:
1. Right-click on the connection, then select Properties.
2. On the Properties tab, select. Request a name and password, certificate, etc. and enable Windows logon domain checkboxes.
3. On the Security tab, clear the Use my login, password, and domain automatically checkboxes, then click OK.
4. Double click the connection, then click Dial.
5. Provide the appropriate username, password, and domain.

650 The remote access server is not responding.
Recommendation: The error can be caused by one of the following:
The remote access server is not running. Contact your system administrator to make sure the server is running.
The line may be too noisy, or your modem could not communicate correctly with the remote access server's modem at the selected speed. For both of these reasons, lower the initial speed (bps) of the modem, then call back.
Check the Hardware Compatibility List to make sure your modem is listed there. Most modern list For supported modems, see the Microsoft website www.microsoft.com. If your modem is listed, contact the modem manufacturer to update the drivers.
The modem's serial cable may need to be replaced.
Possibly incorrect authentication settings this connection. Contact your system administrator to ensure that your authentication settings match the requirements of the remote access server.
The remote access server may have software and hardware compression enabled at the same time. Typically, software compression is enabled on remote access servers, and hardware compression is disabled.

Error 651 The modem reported an error.
Recommendation: Your modem (or other device) has reported an error. If you are connecting through a dial-up line and using a supported external modem, turn the modem off and then on. Close and restart Dial-Up Networking, then call back. If your modem is not supported by Dial-Up Networking, switch to a supported modem. For the most up-to-date list of supported modems, visit the Microsoft website www.microsoft.com. Make sure you have correctly configured your modem for remote access. If this is a virtual private network (VPN) connection, you may have incorrectly entered the TCP/IP address in your network configuration, or the server you are trying to connect to may not be available. To determine if a server is free, contact your system administrator.

Error 652 Modem response not recognized.
Recommendation: Your modem (or other device) gave a message that is missing from one of your script files (Pad.inf, Switch.inf or filename.scp). If you are using a supported external modem, turn the modem off and then on, then call back. If this issue continues to occur, try connecting at a lower initial speed. For the most up-to-date list of supported modems, visit the Microsoft website www.microsoft.com.

Error 653 The macro required by the modem was not found in the device's INF file.

Error 654 A command or response in a device INF section refers to an undefined macro.
Recommendation: One of the Dial-Up Networking configuration files may contain invalid information. If your modem is not supported by Dial-Up Networking, switch to a supported modem. For the most up-to-date list of supported modems, visit the Microsoft website www.microsoft.com.

Error 655 Macro not found in section of .INF file.
Recommendation: One of the Dial-Up Networking configuration files may contain invalid information. If your modem is not supported by Dial-Up Networking, switch to a supported modem. For the most up-to-date list of supported modems, visit the Microsoft website www.microsoft.com.

Error 656 The macro in the .INF file section contains an undefined macro.
Recommendation: One of the Dial-Up Networking configuration files may contain invalid information. If your modem is not supported by Dial-Up Networking, switch to a supported modem. For the most up-to-date list of supported modems, visit the Microsoft website www.microsoft.com.

Error 657 Failed to open device .inf file.
Recommendation: One of the Dial-Up Networking configuration files may contain invalid information. If your modem is not supported by Dial-Up Networking, switch to a supported modem. For the most up-to-date list of supported modems, visit the Microsoft website www.microsoft.com.

Error 658 The device name in the device .inf file or in the media .ini file is too long.
Recommendation: One of the Dial-Up Networking configuration files may contain invalid information. If your modem is not supported by Dial-Up Networking, switch to a supported modem. For the most up-to-date list of supported modems, visit the Microsoft website www.microsoft.com.

Error 659 The media .ini file refers to an unknown device name.
Recommendation: One of the Dial-Up Networking configuration files may contain invalid information. If your modem is not supported by Dial-Up Networking, switch to a supported modem. For the most up-to-date list of supported modems, visit the Microsoft website www.microsoft.com.

Error 660 The device .inf file does not contain responses for this command.
Recommendation: One of the Dial-Up Networking configuration files may contain invalid information. If your modem is not supported by Dial-Up Networking, switch to a supported modem. For the most up-to-date list of supported modems, visit the Microsoft website www.microsoft.com.

Error 661 The command is missing from the device .inf file.
Recommendation: One of the Dial-Up Networking configuration files may contain invalid information. If your modem is not supported by Dial-Up Networking, switch to a supported modem. For the most up-to-date list of supported modems, visit the Microsoft website www.microsoft.com.

Error 662 An attempt was made to install a macro that is not listed in the section of the device INF file.
Recommendation: One of the Dial-Up Networking configuration files may contain invalid information. If your modem is not supported by Dial-Up Networking, switch to a supported modem. For the most up-to-date list of supported modems, visit the Microsoft website www.microsoft.com.

Error 663 The media .ini file refers to an unknown device type.
Recommendation: One of the Dial-Up Networking configuration files may contain invalid information. If your modem is not supported by Dial-Up Networking, switch to a supported modem. For the most up-to-date list of supported modems, visit the Microsoft website www.microsoft.com.

Error 666 The modem is not working properly.
Recommendation: Your modem (or other device) is not responding for one of the following reasons:
The external modem is off.
The modem is not securely connected to the computer. Make sure the cable is securely connected to both the modem and the computer.
The serial cable does not meet the Dial-Up Networking requirements.
The modem is experiencing hardware problems. Turn off the modem, wait 20 seconds, and turn on the modem.

Error 667 The system could not read the media .ini file.
Recommendation: One of the Dial-Up Networking configuration files may contain invalid information. If your modem is not supported by Dial-Up Networking, switch to a supported modem. For the most up-to-date list of supported modems, visit the Microsoft website www.microsoft.com.

Error 668 The connection was terminated.
Recommendation: Call back. If you continue to receive this message, disable the modem's initial speed and disable advanced modem options such as software compression. If this problem continues to occur, contact your system administrator. Also, you must make sure the modem is compatible. For the most up-to-date list of supported modems, visit the Microsoft website www.microsoft.com. If you are dialing manually, make sure you are connected when you click Done. You are dialing manually if you have selected Operator Dialing in the advanced menu of the Dial-Up Networking folder.

Error 669 Invalid use of parameter in media INI file.
Recommendation: One of the Dial-Up Networking configuration files may contain invalid information. If your modem is not supported by Dial-Up Networking, switch to a supported modem. For the most up-to-date list of supported modems, visit the Microsoft website www.microsoft.com.

Error 670 The system could not read the section name from the media INI file.
Recommendation: One of the Dial-Up Networking configuration files may contain invalid information. If your modem is not supported by Dial-Up Networking, switch to a supported modem. For the most up-to-date list of supported modems, visit the Microsoft website www.microsoft.com.

Error 671 The system could not read the device type from the media INI file.
Recommendation: One of the Dial-Up Networking configuration files may contain invalid information. If your modem is not supported by Dial-Up Networking, switch to a supported modem. For the most up-to-date list of supported modems, visit the Microsoft website www.microsoft.com.

Error 672 The system could not read the device name from the media INI file.
Recommendation: One of the Dial-Up Networking configuration files may contain invalid information. If your modem is not supported by Dial-Up Networking, switch to a supported modem. For the most up-to-date list of supported modems, visit the Microsoft website www.microsoft.com.

Error 673 The system was unable to read the usage from the media .ini file.
Recommendation: One of the Dial-Up Networking configuration files may contain invalid information. If your modem is not supported by Dial-Up Networking, switch to a supported modem. For the most up-to-date list of supported modems, visit the Microsoft website www.microsoft.com.

Error 674 The system could not read top speed connections from the media INI file.
Recommendation: One of the Dial-Up Networking configuration files may contain invalid information. If your modem is not supported by Dial-Up Networking, switch to a supported modem. For the most up-to-date list of supported modems, visit the Microsoft website www.microsoft.com.

Error 675 The system was unable to read the connection's maximum carrier speed from the media INI file.
Recommendation: One of the Dial-Up Networking configuration files may contain invalid information. If your modem is not supported by Dial-Up Networking, switch to a supported modem. For the most up-to-date list of supported modems, visit the Microsoft website www.microsoft.com.

Error 676 The telephone line is busy.
Recommendation: Re-dial the number. You can automate redialing on the Properties tab in the connection setup. If it is a virtual private network (VPN) connection, check the name or IP address of the server you are connecting to and try connecting again. Also, contact your system administrator to check if the remote server is running.

Error 677 A person answered instead of a modem.
Recommendation: The modem or other device does not pick up the handset. Check the number and redial it again. If it is a virtual private network (VPN) connection, check the name or IP address of the server you are connecting to and try connecting again.

Error 678 No response received.
Recommendation: This error occurs due to wrong settings VPN connections. Check if LAN is enabled. If the LAN is not enabled, enable it and check if you can access the Internet. If LAN is enabled, check VPN connection type and VPN server address. The VPN connection type should be: PPTP VPN. VPN server address (for all cities where Beeline provides Internet):
vpn. internet. beeline.kz After setting the correct type of VPN connection and the correct VPN server address, check the ability to access the Internet.

Error 679 The system cannot determine the carrier.
Recommendation: The modem or other device does not pick up the handset. Many modems give this error if the remote modem doesn't hang up. Check the number and redial it again. If it is a virtual private network (VPN) connection, check the name or IP address of the server you are connecting to and try connecting again. You can automate redialing on the Properties tab in the connection setup.

Error 680 No beep.
Recommendation: The phone line may not be properly connected to or disconnected from your modem. The number may need to be preceded by a prefix, such as 9, to access an outside line, or the number may be too long.
Make sure the phone line is connected to the correct jack on the modem. Also, make sure you have specified special access numbers to connect to an outside line, such as the prefix 9 followed by a comma.
Check to see if your telephone line has an intermittent tone corresponding to an answering machine message. Many modems cannot dial more than 34 digits. After entering a number exceeding this length, these modems break it into two or more lines, of which only the first (incomplete) is dialed. This happens with USRobotics and Multitech modems. The only known solution to this problem is to use modems from other manufacturers.

Error 681 The modem reports a general error.
Recommendation: One of the Dial-Up Networking configuration files may contain invalid information. If your modem is not supported by Dial-Up Networking, switch to a supported modem. For the most up-to-date list of supported modems, visit the Microsoft website www.microsoft.com.

Error 691 Access is denied because the username or password is invalid in this domain.
Recommendation: Your account is not registered on the specified domain, your password has expired, or you entered the information incorrectly. If you don't specify a domain, the remote access server attempts to verify your username and password against a domain of which you are a member. Carefully retype your username, password, and domain. If you are unsure of this information, contact your system administrator. It is also possible that the funds on your personal account have run out or the billing period has expired. You can check the balance on the statistics server internet. beeline.kz

Error 692 A modem hardware error has occurred.
Recommendation: Your modem (or other device) is not responding for the following reason:
The modem is turned off, not functioning properly, or is not securely connected to the computer.
To solve this problem, do the following:
Reset your modem. See the hardware documentation for more information.
If you are using an external modem, make sure you are using the correct serial cable and that it is securely connected. You can try replacing the modem cable. Also, if you are using an adapter to connect to the serial port, make sure the adapter is properly connected to the modem. For example, a 9-25 pin mouse adapter will not work properly with a serial network connection.
Test the serial port or multiport adapter and replace if necessary.
Make sure the modem handshake settings are correct. For information about the handshake options available for your modem, refer to your modem's documentation.
If your modem is not supported by Dial-Up Networking, switch to a supported modem. For the most up-to-date list of supported modems, visit the Microsoft website www.microsoft.com.
Check if another application, such as HyperTerminal, is using this communication port. If the port is in use, further launch of Dial-Up Networking may cause this message to appear.
Additional information available from the Personal Support Center on the Microsoft website www.microsoft.com.

Error 695 State machines are not running.
Recommendation: An internal error has occurred. Reboot your computer to ensure that any recent configuration changes have taken effect.

Error 696 State machines are already running.
Recommendation: An internal error has occurred. Reboot your computer to ensure that any recent configuration changes have taken effect.

Error 697 Response loop not completed.
Recommendation: An internal error has occurred. Reboot your computer to ensure that any recent configuration changes have taken effect.

Error 699 The modem response caused a buffer overflow.
Recommendation: An internal error has occurred. Reboot your computer to ensure that any recent configuration changes have taken effect.

Error 700 The expanded command in the device INF file is too long.
Recommendation: The script file command cannot exceed 265 characters. Break the team into multiple teams.

Error 701 The set connection speed for the modem is not supported by this COM driver.
Recommendation: Your modem is trying to connect at a speed not supported by the serial port. Reset the initial connection speed to the next lowest standard setting.

Error 703 The connection requires some input from the user, but the application does not allow user interaction.
Recommendation: The server you are trying to connect to requires user interaction. The rasdial command, or the application you are using to connect, does not support user interaction. If this is possible, try connecting using an existing connection from the Dial-Up Networking folder. If you are using a script to connect, try connecting using a connection configured to use a terminal. The terminal window may enable the desired user interaction.

Error 704 Invalid callback number.
Recommendation: The callback number specified in the program is not valid.

Error 707 An error related to the X.25 protocol has occurred.
Recommendation: The X.25 connection reported an error. Contact your X.25 provider to find out why the error occurs.

Error 708 This account has expired.
Recommendation: Ask your system administrator to activate your account.

Error 709 An error occurred while changing the domain password. Perhaps the password is too short or the same as the previous one.
Recommendation: Try changing your password again. If you continue to receive this message, contact your system administrator.

Error 710 A sequence of overflow errors occurred with this modem.
Recommendation: Lower the initial modem speed (bps) and call back.

Error 711 The Remote Access Service Manager failed to start. More information is in the event log.
Recommendation: The Remote Access Connection Management Service may not be running. Configure the service for auto start. Reboot your computer to ensure that any recent configuration changes have taken effect. For more information, visit the Personal Support Center on the Microsoft website www.microsoft.com. The problem may be caused by a malfunction of your modem or modem cable. Make sure your modem is supported by your operating system. For the most up-to-date list of supported modems, visit the Microsoft website www.microsoft.com. Try replacing the modem cable.

Error 712 Bidirectional port initialization. Wait a few seconds and call back.
Recommendation: This error can occur on a connection configured to receive calls (bidirectional connection). The error occurs when you make an outgoing call at the same time that the server is initializing the connection to accept incoming calls. Remote Web Access will re-call after a few seconds.

Error 713 No ISDN lines available.
Recommendation: Make sure your ISDN line is connected correctly and that the terminating resistors are set correctly (see the documentation for your ISDN card), then reconnect. If you continue to receive this message, contact the seller of your ISDN card or your ISDN telephone company.

Error 714 No ISDN channels available to make a call.
Recommendation: All available ISDN channels are busy. Typically, ISDN at the BRI (Basic Rate Interface) level provides two channels through which you can make voice calls and transfer data. If both channels are already in use, Dial-Up Networking will not be able to make a call. Release one channel, then reconnect.

Error 715 Too many errors have occurred due to poor phone line quality.
Recommendation: Too many asynchronous errors occur on the phone line during authentication. Try again. If this problem continues to occur, lower the baud rate and disable all modem settings.

Error 716 The remote access service IP configuration is unusable.
Recommendation: There is a problem with the TCP/IP configuration of the remote access server. For example, your connection is requesting a TCP/IP address from an unused server.
Contact your system administrator to check your server's TCP/IP settings.

Error 717 There are no available IP addresses in the Remote Access service's static IP address pool.
Recommendation: Try to use an IP address that does not cause conflicts on the remote network. If possible, use DHCP to avoid address conflicts.

Error 718 A valid response timed out from the remote computer.
Recommendation: A PPP conversation started but was terminated due to the remote computer not responding for a certain amount of time. This could be caused poor quality lines, or problems on the server. Try connecting again. If it didn’t work out again, then, as a rule, this is due to work on the authorization server, and the problem is fixed within 5-10 minutes.

Error 719 The connection was terminated by the remote computer.
Recommendation: A PPP conversation started but ended at the request of the remote computer. The error may be caused by problems on the server.

Error 720 The connection attempt failed due to a PPP control protocol conflict between your computer and the remote computer.
Recommendation: There are no PPP network control protocols configured for your connection, or the appropriate network protocol has not been installed. This error may occur after changing the network protocol during a software update.

Error 721 The remote computer is not responding.
Recommendation: An attempt was made to start a PPP conversation, but the remote computer is not responding. This error occurs if the server does not support PPP (Windows NT 3.51 and earlier remote access servers or SLIP server). This error can also occur if the server requires login using a terminal window before starting PPP. If using a terminal window to log in solves the problem, for subsequent connections you can automate the login process by using Windows scripts. This error may also indicate a hardware failure on your computer or on a remote server.

Error 722 Invalid data received from the remote computer. The data was ignored.
Recommendation: The received PPP packet is not in the correct format. To resolve this issue, your system administrator needs to keep a PPP event log. For more information, visit the Personal Support Center on the Microsoft website www.microsoft.com.

Error 723 Phone number including prefix and suffix is ​​too long.
Recommendation: Maximum length telephone number, including prefix and suffix cannot exceed 128 characters.

Error 726 The IPX protocol cannot be used to make outgoing calls on more than one modem at the same time.
Recommendation: When using the IPX protocol, only one connection can be used to dial a number.

Error 728 The system cannot find the IP adapter.
Recommendation: Problems with TCP/IP configuration. Reboot your computer to ensure that any recent configuration changes have taken effect.

Error 729 Until IP is installed, SLIP cannot be used.
Recommendation: Check if the TCP/IP protocol is set in the Network Properties.

Error 731 Protocol not configured.
Recommendation: An unconfigured PPP control protocol was queried for specific information. To determine the cause of the problem, ask your system administrator to enable PPP registration using the Netsh.exe utility.

Error 732 This computer and the remote computer could not agree on PPP control protocols.
Recommendation: PPP settings could not be negotiated because the local and remote computer did not agree on a common set of settings. Contact your system administrator for configuration details network protocols, such as TCP/IP, IPX, or NetBEUI. Also, your system administrator can enable PPP registration using the Netsh.exe utility, this may help determine the cause of the problem.

Error 733 This computer and the remote computer could not agree on PPP control protocols.
Recommendation: The server supports PPP, but does not support the network protocols for your connection. Ask your system administrator to configure the connection to use the network protocols supported by your server. Also, your system administrator can enable PPP registration using the Netsh.exe utility, this may help determine the cause of the problem.

Error 734 The PPP Link Control Protocol was terminated.
Recommendation: A PPP Link Control Protocol dialog has started, but was terminated at the request of the remote computer. The error may be caused by problems on the server. Contact your system administrator. Also, your system administrator can enable PPP registration using the Netsh.exe utility, this may help determine the cause of the problem.

Error 735 The requested address was rejected by the server.
Recommendation: Your connection is configured to request a specific IP address. The server is not configured to allow the client to request a specific IP address, or the specific IP address is already in use by another client. If possible, use DHCP to avoid address conflicts.

Error 736 The remote computer has terminated the control protocol.
Recommendation: A PPP Link Control Protocol dialog has started, but was terminated at the request of the remote computer. This means that a specific IP address is specified in the TCP / IP connection protocol settings, and not an automatic one. To fix this, go to Control Panel(controlpanel) – Network connections(networkConnections) , select your connection (Beeline) and use the right mouse button to select Properties(Properties) . Next, go to the bookmark Net(network) , select Internet protocolTCP/ IP (InternetProtocolTCP/ IP) and click on the button Properties(Properties) . In the window that opens, check the boxes Obtain an IP address automatically(ObtainanIP- addressautomatically) and ReceiveDNSautomatically(ObtainDNSserveraddressautomatically) .

Error 737 A short circuit was detected.
Recommendation: The local and remote computers participating in the PPP conversation are the same computer. This usually means that the device (such as a modem) on the link is returning characters back. Try resetting these devices. For non-Microsoft servers, this may mean that the remote computer tries to launch a TTY terminal before connecting. You can configure the connection to open a terminal window after connecting on the Security tab.

Error 738 The server did not assign an address.
Recommendation: The server cannot assign an IP address to your computer from the pool of available addresses.
1. Check the availability of funds in your account.
2. Check your account activity (it may be disabled or suspended).
3. Check availability current tariff on your account.
4. Check if the network and Internet servers are blocked on the personal statistics page.

If you have not found a solution to your problem, please contact Technical Support at 539-500.

Error 739 The authentication protocol required by the remote server cannot use the stored password. Call back and enter the password explicitly.
Recommendation: This error only occurs when establishing a PPP connection to a non-Microsoft production server. The standard PPP authentication protocols used to communicate with other servers require that the password be available in text-only format, but Windows only stores the password in encrypted form for security reasons.

Error 740 An invalid dialing rule was found.
Recommendation: TAPI devices configured for Dial-Up Networking failed to reset or were incorrectly installed. Reboot your computer to ensure that any recent configuration changes have taken effect. If this error continues to occur, check the event log to find out why it occurred.

Error 741 local computer does not support the required type of data encryption.
Recommendation: Checkbox selected. Require Data Encryption (disable if none) on the Security tab, but your connection is not encrypted. Clear this checkbox to use an unencrypted connection, or contact your system administrator. This error can also occur if your password is longer than 14 characters, you have selected the Require Data Encryption (disable if none) checkbox on the Security tab, and you have selected Require Password Encryption in Verify My Identity. Use a password shorter than 14 characters, clear the checkbox. Require Data Encryption (disable if none) and select Allow Unencrypted Password Transmission in Verify My Identity.

Error 742 The remote computer does not support the required type of data encryption.
Recommendation: The requested encryption level is not supported on the remote computer. One of the computers is probably using 128-bit encryption, while the other is using 40-bit, or 56-bit encryption. You need to uncheck the box next to Requires data encryption(Requiredataencryption (disconnectifnone)) in the Internet connection settings. To do this, start an Internet connection and click on the button Properties(Properties) . Next go to bookmark Safety(security) and uncheck the box next to
Requiredencryptiondata
(Require data encryption (disconnect if none)). Click on the button OK and try to connect again.

Error 743 The remote server requires data encryption.
Recommendation: The remote access server requires encryption, but your connection does not have encryption enabled.

Error 751 The callback number contains invalid characters. Only the following characters are allowed: numbers (0 to 9), T, P, W, (,), -, @, and the space character.
Recommendation: Invalid callback number. Only the following characters are allowed in the number: numbers from 0 to 9, T, P, W, (,), -, @ and space. Enter the correct number and call back.

Error 752 A syntax error was encountered while processing this script.
Recommendation: A syntax error was encountered while processing the script. This error is specific to Windows 98/Me. Check your internet connection settings

Error 753 The connection cannot be terminated because it was created by a multi-protocol router.
Recommendation: This connection is used by Routing and Remote Access. Use Routing and Remote Access Service to terminate the connection. The connection will appear either in the list of routing interfaces or in the list of remote access clients.

Error 754 The system cannot find a multi-channel bundle.
Recommendation: An internal error has occurred. Reboot your computer to ensure that any recent configuration changes have taken effect.

Error 755 The system cannot perform automatic redial because this connection has parameters for a particular caller.

Error 756 This connection has already been made.

Error 757 Remote Access Services cannot start automatically. More information can be found in the event log.
Recommendation: An internal error has occurred. Reboot your computer to ensure that any recent configuration changes have taken effect.

Error 758 Internet Connection Sharing (ICS) is already enabled for this connection.
Recommendation: This error can occur if the application enables Internet Connection Sharing while the properties of the connection are open and you are trying to enable the same property. Close and reopen the connection properties. The checkbox must be selected. Allow Internet Connection Sharing.

Error 760 An error occurred while resolving routing.
Recommendation: An internal error occurred while trying to enable routing. Contact your system administrator.

Error 761 An error occurred while allowing Internet Connection Sharing.
Recommendation: An internal error occurred while enabling Internet Connection Sharing. Contact your system administrator.

Error 763 Unable to enable Internet Connection Sharing. More than one LAN connection will be shared.
Recommendation: Close and reopen the connection properties. The Allow Internet Connection Sharing checkbox must be selected. Select Local Area Connection from the list.

Error 764 Smart card readers are not installed.
Recommendation: Install a smart card reader.

Error 765 Unable to enable Internet Connection Sharing. The LAN connection is already configured to use an IP address that is allocated automatically.
Recommendation: Internet Connection Sharing configures the local area network connection of home networks, or small office networks with a static address. There is another network adapter in the system configured with the same address. Change the static address of the network adapter before enabling Internet Connection Sharing.

Error 766 The system could not find the certificates.
Recommendation: Contact your system administrator.

Error 767 Unable to enable Internet Connection Sharing. The LAN connection selected as private is set to use more than one IP address. Change the LAN connection settings.
Recommendation: Remove additional static IP address, or reconfigure the LAN connection for DHCP.

Error 768 Data encryption error while trying to connect.
Recommendation: If there is no need for encryption, disable encryption and try again.

Error 769 The specified destination is unreachable.
Recommendation: The address you provided is not correct, or your remote access server is unavailable. Check the address and try again. Check your LAN connection settings. Delete the existing VPN connection (Beeline) and create a new one.

Error 770 The remote computer rejected the connection attempt.
Recommendation: The remote computer may be refusing to connect to you due to the settings of the calling program, or other hardware settings.

Error 771 The connection attempt failed because the network is congested.
Recommendation: Wait and try again later.

Error 772 The remote computer's hardware is incompatible with the type of call requested.
Recommendation: Contact your system administrator.

Error 773 The connection attempt failed due to a change in the destination address.
Recommendation: Please enter a valid number and try again.

Error 774 The connection attempt failed due to a temporary error. Try connecting again.
Recommendation: Wait and try again later. This error may be due to a timeout or problems with the remote computer.

Error 775 The connection was blocked by the remote computer.
Recommendation: The remote computer may be blocking your connection due to settings in the calling program, a distribution policy that allows access only for a certain amount of time, or other settings.

Error 776 The connection failed because the remote computer entered Do Not Disturb mode.
Recommendation: Contact your system administrator.

Error 777 The connection attempt failed because the modem or other communication device is not working on the remote computer.
Recommendation: Contact your system administrator.

Error 778 Unable to verify server identity.
Recommendation: During the authentication process, the server identified your computer, and your computer identified the server. This error occurred because your computer did not recognize the server.

Error 779 In order to make a call using this connection, you need to use a smart card.
Recommendation: Install a smart card.

Error 780 The trial function is invalid for this connection.
Recommendation: An internal error has occurred. Contact your system administrator. You may need to configure a connection for EAP.

Error 781 The encoding attempt failed because no valid certificates were found.
Recommendation: The VPN client tries to use the L2TP/IPSec protocol to connect. Enter VPN connection settings-Properties->Network->VPN Type and select PPTP VPN.

Error 783 Unable to enable Internet Connection Sharing. The LAN connection selected as private either does not exist or is disconnected. Make sure the network adapter is connected.
Recommendation: Before enabling Internet connection sharing, make sure that the LAN adapter and the appropriate cable are securely connected.

Error 784 This connection cannot be used at boot time because it uses a different username than the smart card user. To use it at boot time, change the used name to the name of the smart card owner.
Recommendation: Set the connection to use the same name as on the smart card. On the Security tab, select the Advanced (custom settings) radio button, and then click the Settings button. Select the Smart card or other certificate radio button (encryption enabled), click the Properties button, and then clear the Use a different username to connect check box.

Error 785 This connection cannot be used during boot because it is configured to use a smart card. Change the properties of this connection to use smart card data.
Recommendation: Set the connection to use a smart card. See Enable smart card or other certificate authentication.

Error 788 The L2TP connection attempt failed because the security layer could not negotiate settings with the remote computer.
Recommendation: Contact your system administrator. The current L2TP settings setting is incompatible with Microsoft's implementation of L2TP.

Error 789 The L2TP connection attempt failed due to an error that occurred in the security layer during negotiations with the remote computer.
Recommendation: Contact your system administrator.

Error 791 The L2TP connection attempt failed because the security policy was not found.

Error 792 The L2TP connection attempt failed because the security negotiation timed out.
Recommendation: Check your Internet connection. If the connection works, contact your system administrator.
Your connection is probably failing for one or more of the following reasons.
The remote server might be down.
The server you are accessing does not have the correct credentials.
Your connection is not configured to use the correct credentials.
Your connection is configured to use a different security method than the remote computer's security method. Try changing the VPN connection type. To change the type of VPN connection, right-click the connection and select Properties, and then view the details on the Network tab.

Error 793 The L2TP connection attempt failed due to a security negotiation error.
Recommendation: Contact your system administrator. Your connection is probably failing for one or more of the following reasons.
The remote server might be down.
The server you are accessing does not have the correct credentials.
Your connection is not configured to use the correct credentials
The computer is using an invalid shared secret. Try a different pre-shared key.
For more information about remote access security, see Security Actions During a Connection.

Error 794 The Framed Protocol RADIUS attribute set for this user is not set to PPP.

Error 795 The Tunnel Type RADIUS attribute set for this user has an invalid value.
Recommendation: The attribute for remote connection must be configured on the remote network. Contact the administrator of the remote network.

Error 796 The Service Type RADIUS attribute set for this user is neither Framed nor Callback Framed.
Recommendation: The attribute for remote connection must be configured on the remote network. Contact the administrator of the remote network.

Error 797 The connection to the remote computer could not be established because the modem was not found or was busy.
Recommendation: This connection requires a modem. Do the following:
Close all programs and try to connect again. It is possible that the modem or the communication port it is connected to is being used by another program.
Make sure your computer has a modem installed. For more information, see Installing a Modem.
Check that the modem is functioning properly. For more information, see Troubleshooting modems.

Error 799 Failed to enable Internet Connection Sharing (ICS) due to IP address conflicts on the network. ICS requires that the host be configured to use the address 192.168.0.1. Make sure that no other network client is using the 192.168.0.1 address.
Recommendation: Check the IP addresses of all computers connected to the local network, change them if necessary. See Configuring TCP/IP Settings.

Error 800 A VPN connection could not be established. The VPN server is unavailable or the security settings for this connection are incorrectly configured.
Recommendation: No access to VPN server. It is recommended to check if there is a physical connection (whether the lights on the network card on the back of your computer are on), whether the network cable is plugged into the connector on the network card and in the socket (if any). Then check if LAN connection is enabled. To do this, follow "Start" ~> "Control Panel" ~> "Network Connections". In the window that appears, find "Local Area Connection" and turn it on if it was turned off.

Check the VPN server address. To do this, go to Control Panel - Network Connections(controlpanel– networkConnections) . Right click mouse, select your connection (Beeline) and in the menu that opens, click Properties(Properties). In a new window in line Computer name (Hostname) or IP address(HostnameorIPaddress) should be written: vpn. internet. beeline.kz(for all cities where Beeline provides Internet). If you saw such values ​​as 8,10,800,10… in the specified line, it means that your computer is infected with a virus. In this case, you need to check your computer for viruses or delete the connection and create it again. Try pinging your local gateway. To do this, click the "Start" button, then "Run". In the line that appears, type in the English layout "cmd", click "OK". In the black window that appears in the English layout, type ping XX.XX.XX.XX (where XX.XX.XX.XX must be replaced with the address of your gateway, the gateway address can also be viewed in the TCP / IP network connection properties) press "Enter ". If the message "Request timed out" appears in the black window one or more times, then call .

Error 868. This is the same. same as 800, but only found on Windows-7. more detailed analysis of their elimination.