Epson diaper reset - Best program! Reset diaper Epson Epson l1300 reset diaper

When the printer is turned on or between prints during operation, Epson automatically starts the print head cleaning procedure. Sometimes, if the print quality drops, you need to start cleaning the print head manually, through the driver. Print head cleaning is done with ink, the pump pumps it through the print head. After that, this ink is drained into a sump or diaper, which is located at the bottom of the printer. A diaper is an absorbent pad and of course it cannot absorb an infinite amount of ink. Therefore, with each cleaning, the printer counts and remembers the amount of ink poured into the diaper. And as soon as, according to the printer, the diaper is overflowing, it gives an error - "Maintenance is required." Printer stops printing and flashes red, drop and paper alternately.

As a rule, the printer counts with some margin, i.e. when the driver says that the diaper is full, in fact, not at all. This is a reinsurance so that a situation does not occur when you tilt the printer, and ink flows out of it onto your carpet. So, for good, the printer should be disassembled, pull out the diaper, wash and dry it, but for the first time, in principle, you can not do this. And so that you never have to pull it out at all, it’s better to pull it out. The ink will merge into a jar standing next to the printer, from which it will not be difficult to pour the ink.

So we figured out the diaper. Now you need to reset the working counter. There are a number of utilities for this.

One of the oldest .

It works on Windows XP, Windows Vista, Windows 7 and works on Windows 8 to a limited extent. With it, you can reset the diapers of old Epsons.

Next utility,

It allows you not only to reset the diaper, but also

Requirements:

Compatibility: Windows XP (x32), (x64), Windows 7.

Language: Russian, English.

Internet: diaper reset is possible only on a computer connected to the Internet.

After starting, the program itself determines the installed printer. All you have to do is press the Reset button. However, not all printer models can be reset for free; for some models, the authors of the program sell reset codes.

Another utility is . Each printer has its own.

With its help, diapers can be reset as follows.

Connect printer. Run the program

Select Particular adjustment mode

Run Consumables maintenance counter (in other versions of Waste Ink Pad Counter)

Click Check - the program polls the printer

if everything is fine - will show the overflow of the counter

check the boxes - Main Pad Countre, Platen Pad Conter

We press Initializatiion - after the end - the program will ask you to turn off and on the printer.

Run counter reset

In new L printers - series, namely L100, L110, L120, L132, L1300, L1800, L200, L210, L300, L312, L350, L355, L366, L456, L550, L555, L566, L655, L800, L810, L850 - NO protection against the use of non-original inks. There are no chips and no codes need to be entered. Pour and print! What the inkjet users dreamed about has come true! CISS - on board! There are no restrictions on the use of different inks! All responsibility is the user's risk.

In the case of use, the issue of refilling comes down to pouring ink into the CISS container and entering the codes that EPSON indicates on the original jars. No blockage, your printer will continue printing just fine after entering the code.

In the case of using inks from alternative manufacturers for the EPSON L series, the code cannot be obtained from anywhere, and the ink level must be reset. This procedure is software, and the PrintHelp program will help us do this.

Filling containers with ink.

The printer's message about the end of ink in one of the containers.

Detach the printer container unit from the printer and place it on a table.

Do not pull out the tanks.

Open the container cover of the printer, then remove the container cover.

Be careful not to spill ink. Make sure the color of the printer container matches the color of the ink being refilled.

Break off the cap cap, remove the cap from the ink bottle, remove the seal, then replace the cap.

Do not throw away the lid cap. If ink remains in the bottle after refilling the container, the cap helps keep the bottle sealed. If you use third-party ink for EPSON L series instead of original inks, it is convenient to refill using special long needles.

Fill the printer container with the desired color of ink up to the upper mark on the container.

If ink remains in the bottle after filling the container to the top mark, close the cap tightly and store the bottle upright until the next use.

Close the lid of the printer container firmly, then close the lid of the container unit.

Install the container unit in the printer.

If you are using , Confirm the ID on the ink bottle, then follow the on-screen instructions to enter the IDs and complete the refill procedure.

If you are using third party inks for the EPSON L series, you will not find identification codes on the cans. Resetting the ink level is done using the PrintHelp program.

"During the active use of an inkjet printer, there comes a moment when the printer refuses to work and displays an error message, requiring you to contact a service center. Depending on the printer model, this error is notified in different ways, but the most standard way to display an error message is to turn blinking of two red LEDs under the printer buttons, and an error window pops up on the computer monitor.

Moreover, a warning about the imminent end of the life of the absorbent pad (diaper) also pops up in the form of a system message on the computer monitor.

After the warning message appears, you have the opportunity to print another 15-20 images (photos) of A4 format, after which the printer will refuse to print until the waste ink counter is reset.

All inkjet printers use a special container to collect waste ink (Waste Ink), which is often called a “diaper” quite often. This "diaper" is a container in which there is an absorbent material that absorbs waste ink well.

Where does waste ink come from in an inkjet printer? Each time it is turned on, the print head is automatically cleaned - a small amount of ink is pumped from the cartridges into the print head, which at that moment is in the extreme right (left) position of the printer, and the ink is "dumped" into the "diaper". Also, when regular cleanings are started through the printer driver, ink is pumped from the cartridges through the print head into the absorber.

Since the volume of the ink collection tank with the absorber in it has a certain limitation, sooner or later, there comes a moment when the tanks overflow and the ink begins to leak out, which causes pollution of both the printer itself and everything that surrounds it. .

To avoid such an extremely unpleasant situation, absolutely all inkjet printers are equipped with a system for monitoring the amount of waste ink. In reality, this system is nothing more than a software counter that counts the number of times the printer has been turned on and all head cleaning procedures performed. Since the volume of ink pumped out of the head during cleaning procedures is approximately known, and the capacity of the sump is also known, it is not difficult to calculate when it is full.

When the value of the counter for the amount of waste ink, supposedly drained into the sump, reaches the value preset in the printer's control program, the printer first issues a warning about the imminent end of the life of the absorbent pad, and soon completely blocks the ability to send a print job.

When the "diaper" of the inkjet printer is overfilled, the service specialist must take the following actions:

replace absorbers - "diapers"
reset (reset) the Waste Ink Counter).

You can reset the "pampers" waste ink counter using the special PrintHelp service program from the SuperPrint development team (Resetters). PrintHelp- universal service program for printers Epson, Canon.

The program can perform the following functions for Epson printers (not for all models):

- checking the current value of the waste ink counter
- reset the waste ink counter (some models require a RESET CODE)
- cleaning the print head
- enhanced cleaning of the print head during initial refueling
- read and write printer serial number
- read and write USB ID
- read and write HEAD ID
- creating an EEPROM backup dump
- paper feed test
- nozzle check and test
- printout of color fills
- initialize (disable) PF deterioration offset
- getting the status of the printer
- read ink level
- reset Ink Level and reset Pampers in printers L100, L200, L800 free

List of supported Epson printer models:

Models for which the diaper reset is carried out WITHOUT the Reset Code are highlighted in green. Resetting a diaper WITHOUT Reset Codes is possible only for countries: Ukraine, Russia, Kazakhstan, Belarus, Moldova, Georgia

Artisan: Artisan 50, Artisan 1430, Artisan 700, Artisan 710, Artisan 725, Artisan 730, Artisan 800, Artisan 810, Artisan 835, Artisan 837

B: B40W, B42WD, B1100, B1110
BX: BX300F, BX305, BX310FN, BX320FW, BX525WD, BX600FW, BX610FW, BX620FWD, BX625FWD, BX925, BX935

C: C58, C59, C62, C63, C64 , C65, C67, C68, C76, C77, C78, C79, C82, C83, C84, C85, C86, C87, C88, C90, C91, C92 , C93, C94, C95, C97, C98, C99, C110 , C120
CX: CX2800, CX2900, CX3300, CX3200, CX3300, CX3400, CX3500, CX3600, CX3650, CX3700, CX3800, CX3900, CX4000, CX4080, CX4100, CX4500, CX4600, CX4700, CX4800, CX4900, CX5000, CX5700F, CX5900, CX6300, CX6400, CX6500, CX6600 , CX7300 , CX7700, CX7800, CX8300 , CX8400, CX9300F, CX9400Fax, CX9500F

D: D68, D78, D88, D92, D120

DX: DX3800, DX4000, DX4200, DX4800, DX5000, DX5050, DX6000, DX7400, DX7450, DX8400, DX9400F

EP: E-600, EP-302, E-600, EP-702A, EP-703A, EP-705A, EP-706A, EP-775A, EP-801A, EP-802A, EP-804A, EP-804F, EP- 901F, EP-902A, EP-903
K: K100, K101, K200, K201, K300, K301

L: L100, L110, L120, L200, L210, L300, L350, L351, L355, L550, L555, L800, L1300, L1800

M: M100, M105, M200, M205

ME: ME2, ME-10, ME-20, ME-30, ME-32, ME-70, ME-80, ME-82WD, ME-100, ME-101, ME-200, ME-300, ME-301, ME-303, ME-320, ME-330, ME-340, ME-360, ME-401, ME-403, ME-510, ME-520, ME-530, ME-535, ME-560, ME- 570, ME-600F, ME-620F, ME-650, ME-900WD, ME-940FW, ME-960FWD, ME-1100

NX: NX110, NX125, NX127, NX130, NX200, NX210, NX215, NX220, NX230, NX300, NX305, NX330, NX400, NX410, NX415, NX420W, NX430, NX510, NX515, NX530, NX620

P: P50, P60
PX: PX610FW, PX650, PX659, PX660, PX700W, PX710W, PX720WD, PX730FWD, PX800FW, PX810FW, PX820WD, PX830FWD, PX-203A, PX-V600, PX-V630
Photo: Photo 820 , 830U , 890 , 900 , 950 , 960 , 1280 , 1290 , 1390 , 1400 , 1410 , Photo 1430 , Photo 1500 , 2100 , 2200
picturemate: PM100, PM210, PM215, PM225 PM235, PM240, PM250, PM260, PM270, PM280, PM290, PM310. diaper reset is NOT available. Reading is available.
PM: PM-3500C, PM-4000px, PM-G800, PM-G4500, PM-G5000, PM-A820, PM-A890

R: R200, R210, R220 , R230, R240, R245, R250, R260, R265, R270 , R280, R285, R290 , R295, R300, R310, R320 , R330, R340 , R350, R360, R380, R390, R800, R1800, R1900, R2000, R2400, R2880 , R3000
RX: RX420, RX425, RX430, RX500, RX510, RX520 , RX530, RX560, RX580, RX585, RX590, RX595 , RX600, RX610 , RX615, RX620 , RX630, RX640 , RX650, RX6080, 670, 6080

S: S20, S21, S22
SX: SX100, SX105, SX110, SX115, SX117, SX205, SX130, SX200, SX205, SX210, SX215, SX218, SX230, SX235, SX400, SX405, SX410, SX415, SX420W, SX425W, SX430, SX435, SX510, SX515, SX525WD, SX600FW, SX610FW, SX620

T: T10, T11, T13, T20, T21 , T22, T23, T24, T25, T26 , T27 , T30, T33, T40W , T42WD, T50 , T59, T60 , T1100 , T1110
TX: TX100 TX101 TX102 TX103 TX105 TX106 TX109 TX110 TX111 TX115 TX116 TX117 TX119 TX120
TX200 , TX209 , TX210 , TX219 , TX220 , TX230 , TX300F , TX320F
TX400 , TX405 , TX408 , TX409 , TX410 , TX419 , TX420W
TX510FN, TX515FN, TX525, TX550W , TX560WD, TX600FW , TX610FW, TX620FWD, TX650 , TX659
TX700W , TX710W , TX720WD , TX800FW , TX810FW , TX820FWD , TX830FWD

Workforce: WorkForce 30, 40, 42, 310, 315, 320, 323, 325, 500, 520, 600, 610, 615, 630, 635, 840, 1100
WorkForce WF-7010, WF-7011, WF-7012, WF-7015, WF-7018, WF-7510, WF-7511, WF-7515, WF-7520, WF-7521, WF-7525
WorkForce WF-2010, WF-2510, WF-2520, WF-2528, WF-2530, WF-2538, WF-2540, WF-2548
WorkForce WP-4011, WPM-4011, WP-4015DN, WP-4020, WP-4022, WP-4025DW, WP-4092, WP-4095DN,
WP-4511, WP-4515, WP-4520, WP-4521, WPM-4521, WP-4525, WP-4530, WP-4531, WP-4532, WP-4533, WP-4535, WP-4540, WP- 4545, WP-4590, WP-4592, WP-4595 - diaper reset is NOT available. Reading is available.

XP: XP-20, XP-30, XP-33,
XP-100, XP102, XP-103, XP-111,
XP-200, XP-201, XP-202, XP-203, XP-204, XP-205, XP-206, XP-207, XP-208, XP-211, XP-212, XP-214, XP- 215, XP-216, XP-217
XP-300, XP-302, XP-303, XP-305, XP-306, XP-311, XP-312, XP-313, XP-315,
XP-400, XP-402, XP-403, XP-405, XP-406, XP-411, XP-412, XP-413, XP-415, XP-510,
XP-600, XP-610, XP-605, XP-615, XP-700, XP-710, XP-750, XP-800, XP-810, XP-850, XP-950

For those printers in which the diaper is made in the form of a separate cartridge with a separate chip, it can only be reset by chip programmers.

Using the program free. All functions are supported incl. and diaper reset function. For some models, this function works after entering

All Epson printers with a continuous ink supply system have a special counter that counts the number of sheets printed by the printer. This counter is needed in order to determine the approximate time for flushing (replacing) the so-called waste ink absorber, or as it is popularly called diapers.

What is a diaper in a printer?

A diaper in a printer is a special plastic container that contains a highly absorbent material such as a sponge. It serves as a collector of ink that is released during the printing of the printer and does not fall on the sheet of paper, for example, when the printer is idle or during the period before and after printing.

This is what a diaper looks like in Epson printers

Adjustment Program - Program for resetting diapers in Epson printers

This program is free and allows you to programmatically reset (zero) the values of diapers and ink levels on Epson printers with CISS with just a few mouse clicks.

There is full support for models L210, L110, L300, L350, L355.

After downloading, unpack the archive with the program. It does not require installation, so after unpacking, you immediately need to run the executable file adjprogcracked.exe.

Running the epson adjustment program to reset the diaper in Epson printers

The main program window will appear, where you need to select the printer model.

Selecting a printer model in the epson adjustment program

A detailed step-by-step instruction with images is also in the archive with the program.

The software version for Epson L130, L220, L222, L310, L360, L365, L366 is .

Perhaps you will be interested in:

Hello to all! Today I will show how to reset the diaper on the Epson XP-302 printer, but this example can be reset on other models. At relatives, the printer began to print in black and yellow. They sent it in for repair, they were told that it was impossible to make it, some codes were needed ... Well, I decided to figure it out ...

At first I thought, I'll do a few calibrations and everything will be decided ... But the printer began to give out this message: The life of the ink-absorbing lining has expired.

I started to google what it is in general) On the Internet there is a program for resetting epson counters, called PrintHelp, but it asks for codes that you need to buy! Well, this is not the case) But on some printers, it turns out to reset Epson diapers for free.

If PrintHelp did not reset the counter for you for free, then on the Internet there is the Epson Adjustment Program (epson forbade it to be uploaded).

If the program does not help, then you can try the SSC Service Utility or. We launch the program to reset the epson diaper. It's called the Epson Adjustment program. So if suddenly it doesn’t work for your printer, then look for another version.

And so, after starting, select the model and port:

If your model is not available, it's okay, just choose like mine.

The main thing is that the drivers are installed. Otherwise, the program will not see the printer port. Click OK and then select Paricular adjutment mode.

Select the waste ink pad counter. This is an ink and diaper counter.

We put all the checkboxes and click Check, thereby we will check the counters.

I have already reset the counter and managed to print a certain number of pages. But if your printer swears at diapers, then in the lower field you will have a value of 100%. Select the top counter and click Initialization, i.e. Epson counter reset.

The program will ask you to turn off the printer.

We press ok, after it turns on and we can check. Highlight the top checkbox and click check again.

As you can see, the Epson diaper reset was successful! But do not forget that Epson does not give out such an error for nothing. In addition to resetting, I also recommend cleaning the gasket under the cartridges.