Tricolor software update 8302. Tricolor tv receiver firmware for free viewing. Where can I download free firmware Tricolor TV

And then, anything happens, and in the midst of a holiday, you can be left without your favorite program.

And so the software update via satellite, receiver GS 8302.

Automatic software update will last until January 25, 2015 inclusive, in the future it will be possible to update it yourself.

In order for the update procedure to proceed correctly, you must turn on the receiver on the Tricolor TV Infochannel TV channel.
After a few seconds, a message will appear on the screen informing you that a new version of the software is available.

If this message appears, confirm the start of the update by clicking OK.

Before starting the update, go to the "Status" menu item and write down the values indicated in the lines "Receiver software version" and "Module software version".

After the update, the receiver software version should change to 1.24.199, and the module software version should remain the same - 02.00.11.

ATTENTION! Do not turn off the power of the receiver until the update procedures are completed! Otherwise, the receiver may be damaged!

To update the receiver software, follow these steps:

Unplug the receiver's power cord from the outlet, and then plug the receiver back into the mains. Switch the receiver to the Tricolor TV Info Channel.

After a few seconds, a message will appear on the screen asking you to update the receiver software in the following form:

When this message appears, select "YES" and press the "OK" button on the remote control.

If you would like to delay the update process, select "No" in the message on the screen. You will be prompted to update the software again the next time you turn on the receiver. You will be able to install the new software at any time convenient for you from December 11, 2014 to January 25, 2015.

After agreeing to update, service messages about the process of updating the receiver software will be displayed on the screen. The message type is shown below. The software update takes about five minutes.

Attention!

During the software update it is forbidden to turn off the power of the receiver! Otherwise, the receiver may be damaged!
After the software installation is completed, the receiver will reboot into the "Setup Wizard" mode.

The first step of the "Setup Wizard" will prompt you to select a language, set a time zone, and select an "Operator". In the "Operator" line, you must set the value "Tricolor TV" or "Tricolor TV-Siberia", depending on the region where your equipment is installed.

Go through the remaining steps of the "Settings Wizard" and search for "Tricolor TV" channels, which will be launched at the last step.

Upon completion of the search for Tricolor TV channels and saving the found ones, make sure that the receiver software version has changed to 1.24.199, and the module software version has remained the same - 02.00.11.

To do this, go to "Menu" -\u003e "Status" and check the value in these lines.

But in addition to software updates, the software update of the Conditional Access Module CI + has been launched via satellite.

Automatic updating will last until January 25 inclusive, in the future it will be possible to update on your own.

In order for the automatic update procedure to work correctly, you need to turn on the receiver on the First HD TV channel or on one of the Basic MPEG-2 TV channels.

After a few seconds, a message will appear on the screen informing you that a new version of the software is available. If this message appears, confirm the start of the update by clicking OK.

You can also upgrade yourself through the CI+ menu of the module.

To do this, you need to turn on the receiver (or a TV with a built-in receiver) on the Tricolor TV Infochannel TV channel, go to the "CI + Module Settings" section and select a software update. After a message about the availability of a new software version appears, confirm the start of the update by clicking "OK".

To start the update, turn on the Tricolor TV Info Channel. After a few seconds, a message will appear on the need to update the module software (the appearance of the messages given in the instructions may differ from the messages displayed by your receiving device):

When this message appears, confirm the start of the update.

If you refuse to update, you will be prompted to perform it again after rebooting the receiving equipment. You will be able to install the new software at any time convenient for you from December 11, 2014 to January 25, 2015.

Attention! If a message about the start of the update does not appear on the Tricolor TV Info Channel, you can start it manually. To do this, on the TV screen, go to the CI + module menu and then open the “Settings” item. Select "download software" and follow the instructions on the screen.

After confirming the start of the update, messages will be displayed on the screen informing about the update process. After the update is completed, the module will automatically restart.

If this does not happen, you can reset the module manually by turning off the receiving equipment from the power supply and turning it on again. You can also remove the module from the CI+ slot and reinstall it.

Good luck Friends!

Happy New Year to you!

Software update version for GS 8302 receiver for Tricolor TV subscribers in the central region.

The use of this software version in the Siberian region is unacceptable, since there is no support for searching for Tricolor TV-Siberia channels.

It will not be possible to return the previous version of the software.

After the update, all channels will be deleted.

The work of the service “Cinema halls “Tricolor TV” has been improved.
The work of the TV Mail service has been improved.
Improved receiver stability.

Before updating, read the instructions in the archive.

Compared to previous software versions:

The Status menu has been redesigned. Two options for displaying information have become available: short (contains the most frequently used data, including information about the ID number); advanced (contains all information about the receiver) - called by pressing the Red button ("F1" or "i") on the remote control while in the "Status" menu.
The general list of TV channels, called by pressing the "OK" button, has been redesigned. Additional lists have become available, the channels in which are grouped according to the subject. Switching through the lists is carried out by the Green button on the remote control from the general list of TV channels.
The "Payment" infomenu has been added - an information block containing a description of the main methods of payment for Tricolor TV services.
Improved EPG performance.
Transponder base and search algorithm have been updated for Tricolor TV-Siberia operator.

Receiver Instructions.

Module software updates:

4. If the software version of your receiver's module is lower than 02.00.11, then in 1-2 minutes service messages about the process of updating the module's software will be displayed on the TV screen. The appearance of the messages is shown below.

5. It is necessary to wait for the disappearance of the service message of the type "Initialization of the module".

6. Next, you need to make sure that the updates are installed. To do this, check the software versions by pressing the "MENU" button on the receiver's remote control and selecting the "Status" item. The line "Software version" should indicate "0.20.107", and the line "Module software version" - "02.00.11"

7. After checking the status of the software (even if the update took place only in one stage: updating the receiver software), you need to reset the receiver to factory settings. To do this, return to the main menu (the “Exit” button on the remote control), go to the “Settings” section and select the “Factory settings” item.

After the pop-up window appears, select "Yes" and press the "OK" button on the remote control.

8. The "Installation Wizard" will automatically launch to complete the software update. Select a language and click the "Next" button. Make sure the settings are correct and click "Next" again.

9. Select the region where you live. If your region is not in the proposed list, select "Main".

10. After selecting the region, an automatic search for TV and radio channels will begin. Save the found TV and radio channels by pressing the "OK" button.

11. This completes the receiver and module software updates. The equipment is ready for further work.

12. If the error message “Failed to update the software” appears on the screen during the update, restart the receiver (power off and then on the receiver) and try the update again.

13. ATTENTION:

Access to the "Tricolor TV Cinemas" package is carried out through a new interface by pressing the "Order a movie" button on your remote control, or through the menu of the receiving equipment (Main Menu \ Applications \ Tricolor TV Cinemas).

The new software is designed to increase the security level of receiving equipment and ensure the stability of its operation, as well as to make its operation more convenient when watching TV channel packages and using additional Tricolor TV services.

A new functionality has been added to the software in the interface of the "Tricolor TV Cinema Halls" package. Some buttons have received additional functions, for example, pressing the Red button brings up a description of the selected movie, Green - options for sorting the list of films (alphabetically, by genre, by nearest screenings, by novelty in the schedule), Yellow - a list of films for which it was installed timer, Blue - a list of films that will be available for viewing the next time the repertoire is updated.

For the convenience of subscribers, the Status menu has been redesigned. After the update, the subscriber will have two options for displaying information:

Brief (contains the most frequently used data, including information about the ID number) - is displayed when you go to the "Status" menu item;

Extended (contains all information about the receiver) - called by pressing the Red button ("F1" or "i") on the remote control while in the "Status" menu.

The general list of TV channels (displayed on the TV screen when you press the OK button) has also been redesigned. Now you can group TV channels into thematic categories, such as Entertainment, Business, Educational, Teleshopping, Foreign, and others. Switching by category is carried out by the Green button on the remote control from the general list of TV channels.

FAQ:

Question: Why do I need to update the software?

Answer: The new version of the software for GS-8302 receivers has a new, more convenient interface for the “Tricolor TV Cinema Halls” service, the “Status” menu has been redesigned, and changes have been made to the system settings of the receiver, which increases its stability.

Question: Why did the Status information window look different? Where did some of the items that were before go?

Answer: For the convenience of subscribers, the Status menu has been redesigned. Now you have two options for displaying information: short (contains the most frequently used data, including information about the ID number) and extended (contains all information about the receiver). So, for example, such items as “Hardware version”, “Module firmware” and Database version” can only be seen in the extended version of the window, which can be called up by pressing the Red button (“F1” or “i”) on the remote control while in the Status menu.

Question: Why have the functional buttons changed in the interface of the Tricolor TV Cinemas package?

Answer: In the new version of the software, additional features of the interface of the "Cinema halls "Tricolor TV" package were implemented. Now, by pressing the Red button, you can read the description of the selected movie, the Green button - select one of the possible options for sorting the list of films (alphabetically, by genre, by the nearest screenings, by novelty in the schedule), the Yellow one - to see the list of films for which it was installed timer, Blue - see the list of films that will be available for viewing the next time the repertoire of the Tricolor TV Cinemas package is updated. Also, the new version of the software implements the ability to display the interface of the “Tricolor TV Cinema Halls” package on the screen when you click on the “Order Movie” or “Split File” button when watching / listening to any TV or radio channel, and not just, as it was before , when watching the TV channel "TV.Poisk".

Question: What is the "Genres" button in the general list of TV channels for?

Answer: This function allows you to group the list of TV channels into thematic groups for ease of navigation. By switching lists, you can choose the most interesting group of TV channels, including Entertainment, Business, Educational, Teleshopping, Foreign, and others.

Manual for updating the firmware of the satellite receiver Tricolor TV GS 8302 via satellite

Before performing the firmware, you need to find out the versions satellite receiver firmware and the module (“Menu” => Status”), make sure that the firmware version of a particular satellite receiver corresponds to version 0.20.30, and the module modification is 02.00.11. Upon completion of the flashing, the software version of the satellite receiver will change the tricolor to 0.20.107.

New software update satellite receiver will be downloaded from the air.

Very important! Do not turn off the power supply of the satellite receiver until the flashing process is completed! Otherwise, the tricolor satellite receiver is likely to fail!

In order to update the software of the satellite receiver, do the following:

Turn off the receiver GS 8302 from the outlet, then reconnect the satellite receiver to the electrical network;
- leave the tricolor TV receiver on the Information channel "Tricolor TV";
- after a while, a sign will appear on the TV screen about the need to update the receiver software of the following form:

When this message appears, press the "OK" key on the satellite receiver's remote control.

If you would like to delay the process of flashing the satellite receiver, select "No" from the notification on the TV screen. You will be advised to reflash the software again the next time you turn on the Tricolor TV satellite receiver. You have the opportunity to make the firmware of the tricolor tv satellite receiver at any period suitable for you from 01/17/2013 to 02/17/2013.

After Confirmation for the update, service messages will appear on the TV screen about the process of flashing the receiver software. The message type is shown below. The software update will take approximately five minutes.

Very important! It is forbidden to turn off the power of the satellite receiver while flashing the software! Otherwise, the receiver is likely to fail!

After the software update is completed, the satellite receiver will automatically turn off, and then connect to the Information TV channel "Tricolor TV"

After that, you need to make sure that the updates are correctly installed. To do this, find out the firmware versions by pressing the "MENU" key on the remote control of the satellite receiver and selecting the "Status" item. The line "Software version" should show "0.20.107", and the line "Module software version" - "02.00.11"

Then, during the switching of television channels, you will be advised to update the list of channels and genres. Confirm the update of the lists by clicking "YES".

At the end of the channel scan, a sign will appear indicating the successful completion of the scan. Click "OK" - the message will disappear. The firmware of the satellite receiver is completed. The receiver is ready for use.

The latest software is designed to improve the security of receiving equipment and guarantee the stability of its operation, as well as to make its use when watching channels and using additional Tricolor TV services more comfortable.

The latest functionality is built into the Firmware in the interface of the “Cinema halls “Tricolor TV” service. Some keys have acquired auxiliary functions, for example, pressing the Red key activates the details of the selected movie, Green - ways to sort the list of movies (alphabetically, by genre, by close shows, by freshness in the schedule), Yellow - the list of movies on which it was put timer, Blue - a list of films that will become available for viewing with the next update of the repertoire.

The Status menu has been changed. After updating the software of the satellite receiver, 2 types of data reflection will become available to the client:

menu "Status" has been changed. After updating the software of the satellite receiver, 2 types of data reflection will become available to the client:

Brief (includes especially regularly used data, including information about the ID number of the Tricolor receiver) - this information is displayed when you go to the "Status" menu item;

Extended (includes full information about the tricolor TV receiver) - called by pressing the Red key ("F1" or "i") on the remote control while in the "Status" menu.

In addition, the general list of television channels (displayed on the TV screen when you press the OK button) has been redesigned. Now you have the opportunity to group TV channels into thematic groups, such as Entertainment, Business, Educational, Teleshopping, Foreign, and others. Switching between groups occurs with the Green key on the remote control of the satellite receiver from the general list of channels.

FAQ::

Question: What is the purpose of software updates?

Answer: In the latest version of the firmware for hd receivers tricolor GS-8302, a fresh, most modern interface for the “Tricolor TV cinema halls” service has been implemented, the “Status” menu has been redone, and additions have been made to the system options of the satellite receiver, which improves the stability of its operation.

Question: As a result, the information window "Status" began to look different? Where did some of the positions that used to be?

Answer: For the comfort of tricolor TV subscribers, the Status menu has been redone. Now 2 types of information reflection are available to you: short (includes more frequently used information, including information about the receiver ID) and extended (stores all information about the satellite receiver). So, for example, such items as “Hardware version”, “Module firmware” and Database version” can only be found in the extended window type, which can be initiated by pressing the Red key (“F1” or “i”) on the remote satellite receiver while in the Status menu.

Question: As a result, were the multifunctional keys modified in the interface of the “Tricolor TV Cinema Halls” package?

Answer: In the latest version of the software, additional functions of the interface of the Tricolor TV Cinemas package interface were implemented. Now, by pressing the Red key, you can read the image of the selected film, Green - select one of the potential types of sorting the list of films (alphabetically, by genre, by nearest screenings, by novelty in the schedule), Yellow - see the list of films for which it was determined timer, Blue - see the list of films that will be available for viewing during the next update of the repertoire of the Tricolor TV Cinemas package. Also, the new firmware version implements the ability to display the interface of the “Tricolor TV Cinema Halls” package on the TV screen by pressing the “Order Movie” or “Split File” button when watching any TV channel, and not just, as it was before, when watching a TV channel "TV.Search".

Question: What is the "Genres" key in the general list of channels for?

Answer: This feature allows you to group the list of TV channels into thematic groups for comfortable navigation through the channels. Switching through the lists, you have the opportunity to find a particularly exciting group of TV channels, including Entertainment, Business, Educational, Teleshopping, Foreign, and others.

On April 12, 2017, new software (software) for GS 8302 receivers was released, aimed at improving and improving the operation of this equipment.

Before starting the update, go to the “Status” menu item and write down the values indicated in the lines “Receiver software version” and “Module software version”.

After the update, the receiver software version should change to 1.25.322, and the module software version to 07.00.00.

ATTENTION! Do not turn off the power of the receiver until the update procedure is completed! Otherwise, the receiver may be damaged!

To update the software of the receiver and the module, do the following:

1. Unplug the receiver's power cord from the outlet, and then plug the receiver back into the mains.

2. Switch the receiver to channel number 333 in the general list.

3. After a few seconds, a message will appear on the screen asking you to update the receiver software in the following way:

When this message appears, select "Yes" and press the "OK" button on the remote control.

4. After agreeing to update the receiver software, service messages about the process of updating the receiver software will start to appear on the screen. Updating the receiver software takes about five minutes.

5. Upon completion of the software update, the receiver will reboot and enter the channel viewing mode.

6. To continue the update, you must turn on the receiver again to channel number 333. Within one minute, a message will appear on the screen asking you to update the module software of the following form:

7. When this message appears, press the OK button on the remote control. The module software update takes about a minute. The type of service messages is shown below.

Attention! Do not turn off the power of the receiver while updating the module software! Otherwise, the receiver may be damaged!

8. After the software update is completed, go to the “Status” menu and make sure that the receiver software version has changed to 1.25.322, . and the software version of the module is at 07.00.00.

9. This completes the receiver software update, and the receiver is ready for further work.

On April 12, 2017, a new software (software) for the receiving equipment of the GS 8302 model was launched, aimed at improving and improving the operation of this receiving equipment.

Before starting the update, go to the "Status" menu item and write down the values indicated in the "Receiver software version" lines.

After performing the update, the receiver software version should change to 1.25.322 .

ATTENTION! Do not turn off the power of the receiver until the update procedure is completed! Otherwise, the receiver may be damaged!

To update the receiver software, do the following:

1. Unplug the receiver's power cord from the outlet, and then plug the receiver back into the mains.

2. Switch the receiver to channel number 333 in the general list.

3. After a few seconds, a message will appear on the screen asking you to update the receiver software in the following way:

When this message appears, select "Yes" and press the "OK" button on the remote control.

5. Upon completion of the software update, the receiver will reboot and enter the channel viewing mode.

6. After the software update is completed, go to the “Status” menu and make sure that the receiver software version has changed to 1.25.322.

7. This completes the receiver software update, and the receiver is ready for further work.