gs 8306 receiver version. Tricolor TV - receiver software update. Problems after firmware

HD Digital Satellite Receiver

IMPORTANT!!! The Stingray firmware for this receiver model with a weak processor is very unstable - possible problems:

loss of picture and sound
flickering when turning on electric devices and lights
freezing and slow channel switching
spontaneous reset to factory settings when the power is turned off
loss of signal from the antenna

It will not be possible to restore the previous version of the software via USB. PS (Only by soldering flash memory and flashing it in the programmer)

Before updating, read the instructions in the archive.

Unofficial software:

Compared to previous software versions:

The operator selection menu has been modernized.
Implemented a new menu interface "Status", which simplifies the work with this menu.
Improved overall receiver performance.
An information block has appeared containing a description of the main methods of payment for Tricolor TV services.

According to the comments of the user vale9041 from the forum http://www.telesputnik.ru

Now it is possible to remember the settings of the receiver through the standby mode, even if it was disconnected from the power supply.

The procedure is as follows:

If you have just created favorites and turned off the receiver with the power cord, then turned it back on, the receiver will go to the tricolor channel, button return with two circular arrows (the so-called LAST ) we will be on the first channel created in the favorite.

If, when viewing a favorite, we transfer the receiver from the remote control to standby mode, then turn it on again, then later, when you disconnect the res from the network with a cord and turn it back on, the return button will return it to the favorites of the channel at which you switched it to standby mode from the remote. That is, the standby mode serves as a memorization.

The same can be done with the volume ... If you set the volume to the maximum, and transfer the res to standby mode, then the next time you turn on the res, the maximum volume will be. But this is on condition that you will later turn off the res with a cord from the outlet.

the same can be done so that the receiver remembers the general list of channels in one column or three columns in width (view)... that is, the standby mode is remembering what we want ...

Past releases

Compared to the previous version of the GS8306 receiver software / GS8305, version 1.0.49 has the following changes:

The algorithm for automatic search of Tricolor TV channels has been improved.
Removed the ability to delete the list of TV and radio channels that are generated by default in the "All TV" and "All Radio" lists.
During the initial setup, the channel number "0" is displayed.
Removed indication of pressing buttons in StandBy mode.
When switching to the list of radio channels for the first time, the receiver is switched on on the radio channel number "0".
Optimized EPG performance
Implemented work with right polarization.
TV Mail Service. The Delete Mail button has been renamed to Delete Mail.
Channel list. The "Width" function button has been renamed to "View".
Fixed incorrect inscription in HDMI mode "Volume scale timeout". In version 1.0.049, the inscription looks like: "Time to display the volume scale."
Confirmation dialog boxes are implemented from left to right ("YES" -- "NO", default cursor is "NO").
Improved the work of the service "Cinema halls "Tricolor TV"
Improved receiver compatibility with TVs when connected to them via HDMI

Receiver firmware via USB service port

GS-8306 does not have an RS-232 (COM) port, but it has a service USB, through which it is flashed. For firmware, we need a regular USB flash drive, and the latest version of the firmware file for the GS-8306 receiver can be downloaded above .

You can check which version of the receiver software you have installed in the Main Menu

DRE Info>Status

Firmware order:

1. File ssu_gsc_stb.upg copy to USB flash without renaming.

2. Insert USB flash into the receiver and reboot the receiver by power, you can do this by pressing the button "stand by" on the front panel of the receiver. As soon as the power is turned on, the firmware process will begin, this will be indicated by a corresponding message on the TV screen.

Now it remains only to wait for the end of the process. When the firmware is finished, a message about the successful firmware will appear on the TV screen.

3. After the permission message to remove the USB flash appears on the TV screen, remove the USB flash.

IMPORTANT! It is not recommended to remove the USB flash drive before the appropriate permission message appears on the TV screen, otherwise the receiver will fail.

A rollback to an earlier version is not possible; in the receiver, you can replace the software with either the current version or a newer one.

If the firmware does not go, then:

We format the flash drive in FAT or FAT32 with any utility, for example from HP for flash drives, but not in Windows, such as right-clicking on the flash drive and the format may not help.

We upload the file to a flash drive.

We insert it into the included receiver, wait a minute as little as possible and turn it off with the button on the device, you can immediately turn it on with the same button.

After 10 seconds, maximum 30, an inscription will appear that the firmware is in progress.

If the inscription does not appear and the standby indicator starts to flicker, then the firmware has not started.

Software update for GS 8305 and GS 8306 receivers via satellite

On March 11, 2013, a software update for the GS8305 and GS8306 receivers will be launched from the Eutelsat W4/W7 (36A/36B) satellites, aimed at improving and improving the performance of this receiving equipment. Tricolor TV subscribers will be able to update the receiver software at any time from March 11 to April 8, 2013.

Before starting the update, write down the current software version by going to "Menu" -> « DRE Info" -> "Status". When the update is completed, the receiver software version should change to 1.1.001 . The new software will be downloaded from the air.

ATTENTION! Do not turn off the power of the receiver until the end of the update procedure! Otherwise, the receiver may be damaged!

To update the receiver software, follow these steps:

1. Unplug the receiver's power cord from the outlet, and then plug the receiver back into the mains.

2. Switch the receiver to the TV channel "Infochannel" Tricolor TV ".

3. After a few seconds, a message will appear on the screen asking you to update the receiver software in the following form:

When this message appears, select "YES" and press the "OK" button on the remote control.

Attention! If a message about the need to update the software does not appear on the TV screen within 5 minutes, you need to reset the receiver to the factory settings (“Menu” - “Settings” - “Factory settings” - “OK”).

4. After agreeing to update, service messages about the process of updating the receiver software will begin to be displayed on the screen. The message type is shown below. The software update takes about five minutes.

Attention! Do not turn off the power of the receiver during the software update! Otherwise, the receiver may be damaged!

5. Upon completion of the software update, the receiver will reboot and turn on in the “Setup Wizard” mode.

6. At the first step of the Setup Wizard, you will be prompted to select the language of the menu and the operator. You must select "Tricolor TV Center", only after that you can proceed to the next step.

7. After finishing the search for Tricolor TV TV and radio channels, you need to make sure that the receiver software version has changed to 1.1.001 . To do this, go to « Menu» -> « DREInfo" -> "Status" and check the value in the third line. If the receiver software version has not changed, you need to turn off and turn on the receiver on the Tricolor TV Infochannel and repeat the update procedure.

8. This completes the receiver and module software update, your receiver is ready for further work.

You can watch a training video about updating the software on the air of the Teleinstructor training channel and in the Video Instructions section on the Tricolor TV website.

Description of the new software version:

The new software is designed to increase the level of security of receiving equipment and ensure the stability of its operation, as well as to make its operation more convenient when watching TV channels and using additional Tricolor TV services.

A new functionality has been added to the software in the interface of the "Tricolor TV Cinema Halls" package. Some buttons have received additional functions, for example, pressing the Red button brings up a description of the selected movie, Green - options for sorting the list of films (alphabetically, by genre, by nearest screenings, by novelty in the schedule), Yellow - a list of films for which it was installed timer, Blue - a list of films that will be available for viewing the next time the repertoire is updated.

For the convenience of subscribers, the Status menu has been redesigned. After the update, the subscriber will have two options for displaying information:

Brief (contains the most frequently used data, including information about the ID number) - is displayed when you go to the "Status" menu item;

Extended (contains all information about the receiver) - called by pressing the Red button ("F1" or "i") on the remote control while in the "Status" menu.

FAQ:

Question: Why do I need to update the software?

Answer: The new version of the software for the GS8305 and GS8306 receivers has a new, more convenient interface for the Tricolor TV Cinemas package, the Status menu has been redesigned, and changes have been made to the system settings of the receiver, which increases its stability.

Question: Why did the Status information window look different? Where did some of the items that were before go?

Answer: For the convenience of subscribers, the Status menu has been redesigned. Now you have two options for displaying information: short (contains the most frequently used data, including information about the ID number) and extended (contains all information about the receiver).

Question: Why have the functional buttons changed in the interface of the "Tricolor TV Cinema Halls" package?

Answer: In the new version of the software, additional features of the interface of the package “Cinema halls “Tricolor TV” were implemented. Now, by pressing the Red button, you can read the description of the selected movie, the Green button - select one of the possible options for sorting the list of films (alphabetically, by genre, by the nearest screenings, by novelty in the schedule), the Yellow one - to see the list of films for which it was installed timer, Blue - see the list of films that will be available for viewing the next time the repertoire of the Tricolor TV Cinemas package is updated. Also, the new version of the software implements the ability to display the interface of the “Tricolor TV Cinema Halls” package on the screen when you click on the “Order Movie” or “Split File” button when watching / listening to any TV or radio channel, and not just, as it was before , when watching the TV channel "TV.Poisk".

GS 8306 upgrade from USB to new version 1.9.160, start

GS 8306 waited its turn and we update it via USB. For this we have a new software version 1.9.160. Let's see what difficulties can be during pouring. Because, unfortunately, updates on the operator's receivers have not been going very smoothly lately.

GS 8306 v.o. 1.9.160

GS 8306 update progress

2. The receiver starts the update process. The whole button is lit, there is no image on the screen! It is impossible to check the update process on the screen, both receiver outputs do not work!

GS 8306 v.o. 1.9.160, top diode.

3. At the receiver, one diode glows constantly, the second blinks occasionally. This is all normal, the main thing is not to turn off the receiver from the network! If you turn off the power now, the receiver will fly away for a long time!

GS 8306 v.o. 1.9.160, the update process is complete.

4. After the receiver has loaded everything, both diodes will turn off! We wait at least 10 seconds. If you turn it off earlier, the receiver will be damaged! Sure, it's scary, but that's how it's done...

GS8306 p.o. 1.9.160 inclusion.

5. After everything has been updated, turn off the receiver from the network. We take out the flash drive from USB. Turn on the receiver and set up all programs.

GS8306 software version 1.9.160 check in status.

That's all, we have updated our receiver, now we can watch TV programs. The main thing to remember is that during the update, our receiver may break down and this is not a joke. The majority of users will not be able to repair the receiver on their own.

If you still have doubts about how to upgrade, watch the video. In this video, all the updates take place in real time.

We will add another video about this firmware.

Deterioration of signal quality, incorrect tuning of Tricolor TV channels may indicate that the receiver software version is outdated. To eliminate control errors, get rid of malfunctions and even expand the range of capabilities of the Tricolor TV GS-8306 receiver, you need to update the software. You can cope with this task without contacting a specialist, it will take about a third of an hour, a little knowledge on how to flash the equipment available at home, and its subsequent configuration.

Preparing for a software update

Before flashing the receiver, you need to make sure that the device is confidently receiving the signal. Due to the fact that the software will be installed directly via satellite, any technical failure can be fatal for the receiver. For the same reason, it is necessary to ensure uninterruptible power supply, otherwise it may not turn on at the next start.

If you are out of town in windy weather, a thunderstorm, or periodic power outages occur in a given period of time, then it is better not to risk it and postpone the procedure for a while.

How to reflash the receiver yourself

The firmware will take you about 20 minutes, but at this time you must not ignore the instructions and turn off the receiver or TV. The sequence of actions is as follows:

If there are doubts about one's own abilities, as well as fears that the set-top box may no longer turn on due to an interruption in the data download process, it is better to contact a service center.

The company's specialists can not only reflash the receiver, but also produce equipment diagnostics. In this case, it is worth knowing in advance about the cost of the services provided and the timing of their implementation.

What will the new firmware version change

The processes of information exchange and improvement of communication channels do not stand still. In order to improve picture quality and sound quality, developers are working tirelessly to create a new software environment. Although the devices in users' homes will remain old, timely software updates can expand functionality and make the interface of the satellite set-top box more simple and convenient.

Do not forget that a new software version for the GS-8306 Tricolor TV model is scheduled for release in 2017. So, you can not miss the opportunity to have improved quality satellite television at home or in the country.

Opportunities will open before you:

sorting films alphabetically, by genre and time of showing;
reading descriptions of films and series that interested you;
Set a timer to turn on selected browsing sessions.

Summing up

Now you know exactly how to update the software of your Tricolor GS-8006 receiver . Detailed instructions will certainly help to maintain the correct operation of the equipment throughout the entire service life and not spend money on the help of specialists. In addition, it becomes possible, without changing the device, to expand the functionality of the set-top box and change the interface, which with each new version becomes more intuitive, understandable and attractive.

Firmware SPI Flash W25Q128BVFG receiver GS 8306

This article is devoted to restoring the performance of the satellite receiver GS 8306 / GS 8305 designed to view the channels of the satellite operator Tricolor TV.

Previously, we published two articles on the topics: “GS 8306 receiver operating modes”; “GS 8306 firmware update”, however, as practice has shown, not all the methods described in these articles brought the receiver to work.

We regularly receive questions about returning the receiver to working condition with the following symptom:

both LEDs on the indicator of the GS 8306 receiver are constantly on, the receiver does not respond to the commands of the remote control.

The cause of this condition is most likely a "flying" firmware GS 8306 Tricolor, causing the GS 8306 receiver to not turn on. Automatic firmware GS 8306 Tricolor from an external USB drive in most cases does not lead to success.

The way out of this situation is the SPI Flash firmware, which is located on the motherboard of the GS 8306 satellite receiver.

To carry out repair GS 8306 Tricolor You will need to have a chip programmer and a soldering station available. Without these devices, it makes no sense to start work on restoring the operability of the receiving equipment. If all of the above devices are at hand and you know how to use them, then you can start repair GS 8306 Tricolor.

The first step is to provide access to the GS 8306 motherboard, which contains the SPI Flash chip required for the firmware. To do this, we disassemble the case of the GS 8306 receiver, twisting the screws and nuts located on the rear and bottom panels.

Having unscrewed the screws, you can remove the back panel and the top cover of the GS 8306 digital set-top box. Access to the motherboard is immediately opened.

The board itself can not be unscrewed from the base of the receiver case, since it will in no way interfere with the removal of the SPI Flash chip from the board.

The next step in recovery will be soldering the microcircuit, for which we use a soldering dryer to heat up the places where the microcircuit legs are soldered to the contact tracks of the board. After sufficient warming up, the microcircuit is removed from the board without much effort.

Next, through the adapter with the help, you need to load a working dump into the microcircuit firmware GS 8306 Tricolor: 1.1.001 or 1.2.001 , (dump firmware GS 8307 Tricolor: 1.0.015 ) at the same time we make sure that the microcircuit itself is working, otherwise we replace it.

After firmware GS 8306 Tricolor will be flooded into the microcircuit, it is necessary, observing the marks on the microcircuit and the key on the motherboard, to solder the chip into place, visually making sure that all the legs of the microcircuit have contact with the contact tracks.

Before assembling the GS 8306 receiver, we will make sure that it is working, for which we connect the satellite dish, power supply and audio-video cord to the appropriate connectors.If the firmware was successful and we did everything correctly, then the menu sections of the GS 8306 receiver will appear on the TV screen.

In the receiver’s “status” menu, we specify whether the firmware version of the receiver corresponds to the latest current version (at the time the article was published on July 19, 2016, the current firmware version is 1.2.001). If the firmware version is different, download the latest firmware version from official sources and update the receiver using an external USB drive. How to do this, you can find out in our article."GS 8306 Firmware Update" . We again go to the "status" menu and check that the firmware version has been updated to the latest.

Later, you can assemble the receiver and enjoy watching your favorite TV channels.

P.S. After launching automatic updates for GS 8306(8305) and GS 8307(8308) receivers in September 2016. from the satellite, we began to receive a lot of questions about bringing the GS 8306 and GS 8307 receivers into working condition, on which all stages of the firmware update were not completed, as a result of which the receivers did not boot.

To restore the receiver to work, you need to flash the SPI Flash chips in the GS 8306 receiver or SPI Flash in the GS 8307 receiver, using the working version of the firmware in a similar way.

After restoring the firmware or replacing a microcircuit with a working firmware, we look for an alternative firmware on the network, version 1.2.21789 for GS 8306 or 1.0.21789 for GS 8307 (in which auto-update from the satellite is disabled) and install it from a USB flash drive.

If you do not have a programmer or soldering station at your disposal, make repair GS 8306 Tricolor and GS 8307 you can contact our company atKirov, Solnechny proezd, 8, t. 44-13-50 .

You can also order a microchip from us

It is difficult to imagine modern residents without the Internet, mobile communications and, of course, satellite television. Since digital TV is quite in demand today, a large number of companies provide such a service. However, quality is important to Russians, so they prefer Tricolor TV. It is this provider of digital television broadcasting that has the largest viewership.

By becoming a subscriber of Tricolor TV, residents of Russia get access to many channels on a wide variety of topics. The operator has taken care to provide relevant content to both adults and children. For example, the "Children's" package will appeal to any kid, and parents will not miss the opportunity to enjoy bright and interesting cartoons, fairy tales, educational programs. Sports fans and lovers of erotica will also be satisfied - there are channels of this genre for them.

Activation of the "Single" service is an opportunity to watch more than 200 TV channels of a musical, informational, entertainment nature, as well as all kinds of films, series and much more.

However, it is worth remembering that by connecting the package, it is necessary to renew its validity in a timely manner. Only in this way will you have access to all channels included in the service. It is easy to do this - you just need to choose a convenient payment method. And Tricolor TV has plenty of them. How to pay for Tricolor?

First of all, specify the ID of the receiving equipment, because without it it will not be possible to make a payment. This number can be found in the "Status" section (select from the menu).

And now more about payment methods:

Credit card holders can pay for Tricolor with a bank card(the card must belong to the partner bank of the TV provider)
You can pay for the package at any postal and banking branch of Russia (the bank must cooperate with the operator)
On sale there are special payment cards - scratch cards. It is enough to enter a certain code and the service will be extended
One of the ways is electronic payment systems - Yandex.Money, WebMoney, QIWI, etc. That is, it is possible Tricolor payment via the Internet. You will need to have the required amount on your e-wallet (some systems charge a fee - keep this in mind)
Today, many subscribers use Internet banking to deposit money ( Tricolor payment online) - it's fast, convenient and you don't need to leave your home
Almost every small shop, not to mention supermarkets, etc., has payment terminals. We find the appropriate section, enter the necessary information and deposit cash
You can pay for Tricolor TV packages at Euroset, Svyaznoy and other communication stores
You can transfer the required amount from your mobile phone account

It should not be forgotten that when Tricolor payment, personal account also good for this. Each subscriber has his own account with funds (optional). If the required amount is available, then you can use this method.

If you want to always have access to all channels included in the connected service, do not forget to renew it in time. Otherwise, at one point you will not be able to watch your favorite shows or movies.