Cable for connecting the tricolor receiver to the TV. How to connect a TV set-top box or connect a receiver to a TV. Connecting via analog low-frequency connectors

Have you made a long-awaited purchase and wondered how to connect the new Tricolor receiver to your TV without any problems? Now there are many specialized communities on the Internet, where detailed step-by-step instructions for connecting certain models are laid out, and the manufacturer himself is interested in making his device as accessible as possible in terms of connecting out of the box. Due to the constant debugging process on the part of the manufacturer and the increase in the knowledge base on the part of the communities, the digital set-top box is no longer a rare guest in the apartments and houses of Russians.

All Tricolor prefixes have letter designations:

Cable connection - abbreviation C on the box.
Ground receiver - letter T.
Satellite receiver - S.

Tricolor offers a wide range of satellite devices. Old and side by side in stores, and the choice is not always in favor of the latter. The fact is that the division into “old” and “new” is only formal, some devices were produced for no more than two months, giving way to the next generations. There is a significant difference between the models. For example, a number of interfaces that can be found on the rear panel of the receiver:

HDMI cable.
Antenna high frequency output.
Tulip.
SCART wire

Receiver connection diagram

Antenna output and SCART are inherent in the old generation of set-top boxes. Some modern models only have HDMI. Before purchasing equipment and connecting it to the provider's network, you should compare all the pros and cons, ask the consultant about the speed with which the device is turned on, as well as its technical characteristics.

It will not be superfluous to turn on the receiver in the store, carefully study the package (cables and adapters that can change) and listen to all the seller's recommendations before agreeing to a purchase.

All provider devices are pre-configured and do not require additional manipulations, however, difficulties may arise in terms of hardware, for example, the lack of necessary adapters. However, the old cable from the receiver does not have to look for a replacement, most often it also fits a new device.

Connecting a special Tricolor receiver to your TV will be easier if you know some of the nuances in advance.

For finer tuning, you need to turn on the receiver and see what firmware it has. If necessary, her.

Let's consider the algorithm , how to connect the receiver via cable:

The jack output on the TV is connected to the device with a cable.
Both devices turn on. The receiver displays the channel number.
On the TV remote control, press "0" and use the search. Autoscan will stop at the operating frequencies of your Tricolor set-top box.
If the device is connected correctly, the message “no signal” is displayed on the TV screen.

Another way is to connect to LCD panels:

To connect, you need a SCART wire or, in other words, “bells”.
The cable is inserted into the socket on the receiver, the other end of the wire, respectively, to the TV, after which it should be turned on.
The device will show the serial number of the TV channel.
On the remote remote control you need to press A / V, this will help you switch to video mode. Next, you have to find the connection we need in the menu. When connected correctly, you will see the message "no signal".
If it still did not appear (or the inscription is different), then something was done incorrectly. Next, hold down the buttons 0, 1 on the remote control.
The picture will be displayed as soon as the signal is received (find out what to do if). Below you can see all the information about the received TV channel. To display the signal level, on the remote control you need to press the "i" button a couple of times. These scales will help in the further search for a signal from the satellite.

Connecting the receiver via SCART and HDMI

If the text version of the Tricolor receiver connection diagram is not entirely clear and clarity is required, we recommend that you watch thematic videos.

Summing up, it should be noted that connecting the receiver to the TV is not difficult, since the kit always has a detailed step-by-step instruction Moreover, as noted earlier, today this process is maximally simplified and automated. By the way, you can install the Tricolor system not only on one, but also, but if you wish, you can.

Content:

Tricolor TV refers to satellite television that broadcasts Russian-language terrestrial channels in digital quality. First of all, this package is used by remote areas located in the European part, where conventional terrestrial channels have very poor quality, or their reception is generally impossible. Therefore, at present, users are increasingly asking how to connect Tricolor TV to a TV.

Tricolor TV confidently receives television channels, regardless of the distance to TV towers, the power of repeaters, interference and other problems that often affect broadcasting. This is one of the main advantages of digital broadcasting, since the signal from the satellite is transmitted to the equipment installed directly at the user. Tricolor TV covers vast territories, with high signal quality and a large number of channels.

How to connect the Tricolor TV package

To connect to digital broadcasting, you need a satellite dish, the so-called dish and optional equipment in the form of a receiver (aka tuner) and a convector. After installing the antenna, it is connected to the TV through the receiver.

On the rear panel of the receiver there are LNBIN connectors that are connected to the convector. An antenna cable is connected to the LNBOUT connector high frequency. There is also a connector in which the power supply is connected. In addition, there is a connector through which it is updated software tuner. Depending on the firmware of the receivers, the signal can be transmitted either to all outputs, or to one of them.

After all the cables are connected, you need to turn on the TV and receiver. In case of normal operation, the message “Boot” will appear on the display of the receiver. Then, the channel number will appear instead. It is necessary to search for channels on the TV until the message "No signal" appears. This indicates that the receiver is connected correctly. The connection must be made very carefully, paying special attention to the choice of cable connectors.

Connecting multiple TVs

When deciding how to connect Tricolor TV to a TV, an additional question arises about the possibility of connecting several television receivers at once.

According to experts, you can connect as many TVs as you like. However, in this case, the same channel will be broadcast. To switch channels, you must use a radio remote control or a radio extender. In order to watch different channels, a separate Tricolor TV receiver must be installed for each TV.

How to connect tricolor tv to 2 TVs

Digital television, wireless Internet Today they are no longer something special, available to almost everyone. The price of the service is low. True, not every TV (in the case of satellite TV connection) is able to support this format. This requires special equipment that converts digital signal to analog.

Why do you need a receiver? This is a device that sees satellite television signals, converts digital codes into analog ones and transmits them to a TV (for example, samsung). To make the signal clearer, and in order to connect the receiver, it is best to use only one wire. Thanks to this, switching of signal sources can be carried out on the receiver itself. And the TV at the same time it will be enough just to turn on. The most popular provider today is the wireless Tricolor TV.

From this follows the first rule of connecting the receiver - connect it to a TV or computer in such a way as to ensure the maximum quality of signal reception. According to the degree of quality reduction, several connection options can be distinguished (if we are talking about a video image):

HDMI wireless.
Component.
S video.
Composite.

For an audio antenna, the choice becomes even smaller:

HDMI (not yet available everywhere);
digital (optical or coaxial);
analog RCA connection.

The second important point can be formulated in this way: the simpler the better. This means that the receiver for the TV should have as few wires as possible. True, in this case the number of users will matter. If more than three, ease of connection will come in handy. If the number of viewers is minimal, you can focus on quality, install a receiver, where there will be several connecting contacts. The third rule is that the cable should not be cheap and have an excessive length. A short wire "sees" the signal better. But at the same time, its length should be such that you can freely check the connection by unfolding the monitor.

Ways to connect a Tricolor satellite dish to a TV

There are at least a few popular options for connecting the receiver to a TV:

HDMI connection (by the way, some samsung models support it). The preferred option due to High Quality both audio and video signals. one end HDMI cable connects to the output on the back of the receiver, and the other to the TV, if there is a socket for the appropriate connection.
The composite connector is the simplest, but the picture quality leaves much to be desired.
The S-video port is connected more than one wire, but at the same time it allows you to get a clearer signal from the Tricolor antenna, but the color reproduction is a little poor.
RCA, which are also called "tulips". This is a three-wire component interface that can be used for plasma panels and LCD monitors (samsung, for example). Image quality in terms of color and clarity is quite acceptable.
If SCART is used, then the TV receiver is connected in one of three ways: S-video, composite or RGB. Of all the analog ones, by the way, it is the highest quality.

The Tricolor scheme when connected has its own characteristics, more on that below. In any case, the connection wireless network the Internet, satellite channels etc., you can install it yourself, or you can invite professionals. In the latter case, you can be sure that everything will be done quickly and efficiently. The asking price is by no means exorbitant. Convenient, comfortable and fast. Immediately after the completion of work, you can watch your favorite programs and movies.

The nuances of connecting a Tricolor antenna to a TV

The receiver for Tricolor can be connected using an antenna cable. To do this, you need to connect the receiver through the antenna cable through the antenna jack on the TV.
After that, you need to turn on the TV and receiver. The channel number will appear on the receiver's display. Now on the TV remote control, press the "0" button and start searching for satellite TV channels. Auto scan stops at the frequency the receiver is tuned to. If the connection went well, then the message “no signal” will appear on the TV screen (say, samsung).

There is another option for connecting to satellite signals - using a cable with a bell or Scart connector. First, the receiver is connected to the TV with the right cable and turned on. The channel number also lights up on the display. To switch to video mode, press the A/V button on the TV. The desired antenna connector is selected through the menu. As in the first case, an inscription about the absence of a signal should appear on the screen.

On the Internet you can find information about how exactly such an inscription should look. If something went wrong, or there is no inscription at all, then the receiver is not connected correctly and the TV does not see the satellite TV signal. In this case, simultaneously press the "0" and "1" buttons on the remote control. This is done in order to communicate with satellite equipment. As soon as the antenna signal is found, the channel will show the picture. Information about the enabled channel will be visible at the bottom. In order to see the scale of the signal quality and its strength, press the "i" button on the receiver's remote control. Why is it needed in this case? In order to more successfully search for a signal from the satellite.

The whole world has long switched to digital television. Our country has begun the process of transition from analog signal transmission relatively recently. Digital television has contributed to the emergence of digital channels broadcasting throughout the country. TVs that support digital broadcasting DVB-T2.

It is very convenient, just connect the TV cable to the TV, and no other wires are required. However, if the TV does not support digital broadcasting, then a digital prefix comes to the rescue. Many, having purchased this device, do not know how to properly connect it to the TV. Therefore, this information gap needs to be filled.

Required equipment

In order for digital television to broadcast in the apartment, the following equipment is required:

television;
receiver;
antenna or satellite dish.

The TV should be such that it has an input for the antenna, connectors for "tulips", scart - an input with a video input. Modern TVs have an HDMI connector, it is also suitable for connecting a receiver.

Before purchasing a set-top box, you need to familiarize yourself with the list of companies providing digital television broadcasting services. Can consult with experts selected company, who will advise the necessary model of the receiver. Some companies hold promotions that allow you to purchase and install the device for free.

The set-top box itself is just an attribute that allows you to receive and tune channels for a specific TV, broadcast in a completely new format and much more best quality. In order for them to broadcast through the receiver, you should deal with the broadcast source. It could be:

the Internet;
satellite dish;
other similar items.

However, you should not puzzle too much over this issue, you just need to contact the service providers who will explain everything in detail and in an accessible way.

How to connect a digital set-top box

Such a prefix can be connected not only to a TV, but also to a DVD.– player and monitor. If the receiver is not connected to a TV, you will need to special adapter to connect the cable to the device. This adapter is available at any electronics store.

Connecting the set-top box to the TV is as follows:

After that, it remains only to configure the digital receiver.

Set-top box setup

You need to set up the digital set-top box as follows:

you should take the remote control of the set-top box and press the "Menu" button;
a window will appear in which you need to select the "Configure channels" item;
press "OK" and wait for the set-top box to automatically tune the channels;
then you need to accept the discovered channels and store them.

Thus, setting up the receiver is quite simple.

Connecting a digital device to an old TV

Many people still use old models of TVs. If the prefix is attached to modern models quickly and easily, then old "electrons" do not have a connector for "tulips".

Some older TVs don't have an A/V input, but they do have a SCART socket, some of which accepts component signals. Therefore, you can find the “tulips” to SCART adapter circuit yourself and solder it.

In addition, you can purchase an adapter from audio-video to SCART. It is of two types: adapter cable and the adapter itself, to which a standard RCA is connected - a cable from the set-top box.

Old Soviet TVs of the Elektron type are not equipped with any inputs at all, so only the antenna jack should be used, where a high-frequency modulated signal is fed. Thus, it will be necessary to find a modulator with RCA inputs.

Conclusion

Having connected digital television, do not forget to pay every month for a certain package of channels. Some providers offer the purchase of digital set-top boxes with a set of digital TV channels which are already included in the price.

The main thing is from time to time to be distracted from watching your favorite TV shows in order to devote time to your family.

The variety of audio-video connections sometimes frightens with its abundance and the user is not able to choose the right connection to the Tricolor set-top box to the television receiver. A fair question arises; how to connect tricolor receiver to tv by yourself?

The most expensive set of equipment for receiving a digital signal from a satellite is a receiver. And in order to immediately eliminate misunderstandings, when buying a tricolor set-top box, it is advisable to check the list of recommended equipment on the official website and choose the receiver that suits you.

What are the connections and how to choose the right signal source

In addition to the main power cord, through which the satellite TV receiver is turned on, the following audio-video outputs can be found on the rear panel:

analog RF;
composite audio-video output AV;
S-Video format;
SCART format;
component output Y Pb Pr;
HDMI (High Definition Multimedia Interface).

Let's take a look at each of them in order and determine the appropriate type of connection for your digital satellite receiver.

Analog RF is an outdated video and audio signal transmission format, used earlier as an antenna input for receiving analog television and radio broadcasts.

Composite audio - video output AV - the most common type of connection that can be found on almost any TV or satellite set-top box. In the common people, this type of connection was called the March flower - “tulips”.

You can use multi-colored cables if you still have an old-style CRT television receiver. In order to connect it yourself, just connect the corresponding colored ends of the cable to the sockets on the set-top box and TV.

The S-Video format is the most interesting connector, which is very similar to connecting a keyboard or computer mouse With system unit. It can be found on more expensive models of TVs and receivers. It resembles a round socket with several contacts inside.

The SCART format is a common type of connection between a receiver and TV, a European standard through which video and audio signals simultaneously pass. The picture quality when connected via SCART is comparable to the image obtained when connected via the component video output. It is a thick cable at the ends of which there are connectors with 21 pins. In order to independently dock the TV and the receiver, it is enough to connect the corresponding ends to the sockets on the set-top box and the television receiver.

Component Y Pb Pr is a type of cable connection that is capable of transmitting a high-definition signal, up to 1080i. The cord is a set of multi-colored cables that transmit a signal corresponding to their color.

Green is for HDTV transmission Luminosity Y
Red HDTV Cr\Pr Chroma
Blue HDTV Cb/Pb Chroma
As well as additional, red and white for sound channels.

In order to independently connect the tricolor receiver via a component cable, you must carefully read the instructions and not confuse the cables. Most TVs and receivers are equipped with this type of connection. This is due to the fact that the channel can transmit a high-resolution picture without a significant loss of quality. If your TV allows you to connect in this way, you should not refuse such a choice. The output image will differ significantly in quality from previous connection methods.

HDMI (High Definition Multimedia Interface) is a modern data transfer format between the tricolor receiver and your TV. advantage HDMI connections is to bypass additional conversions in the video signal transmission process. That is, the digital signal enters the TV in the form in which the telecom operator broadcasts and does not change.

For pairing your receiver to your TV, the best option is an HDMI connection, if your receiver and TV have one. Since satellite TV channels are moving to new standard broadcasting. And tricolor TV is no exception, it is slowly refusing to broadcast its TV channels in MPEG 2 and MPEG 4 formats and is switching to HD broadcasting. Therefore, it is advisable to use a connection that can transmit the broadcast picture to TV with the highest quality.

Schemes for connecting the tricolor receiver to the TV

Connecting a digital receiver to a TV can only be done using certain connecting cables. The circuit is very simple; you need to take a suitable cable and connect it to the corresponding output of the set-top box, the other end to the same jack to the TV. If there are difficulties in determining the necessary outputs, you can use the diagram shown in the figure.

The scheme for self-pairing two TVs is slightly different from the first task, but these differences are not significant. So, in this case, we need a second, longer cable for the second TV. If in the first case you use a connection using tulips, then another connection must be selected for the second television receiver, for example, SCART or HDMI.

It should be noted that the second TV will show the same channel as the first one, since the TV signal from the tricolor set-top box is turned on and controlled. In order for the second TV to show a picture independent of the first, you need to purchase a second receiver. An additional receiver turns on and works through the same antenna as the first one, only a separate output on the converter is used. In this case, both receivers will work independently of each other.

An important point for independently connecting the set-top box to the TV is to use the minimum number of wires. Also, you should not make a connection with deliberately long cables, since a long cable loses part of the signal.