What keys to press to connect to the Internet. How to enable Wi-Fi on your laptop. Enabling via Device Manager

The question of turning on wi-fi on a laptop is of interest to many. Difficulties can arise due to the fact that each model has its own recommendations and instructions. Sometimes a key combination is sufficient, in other cases a mechanical switch is used.

Turn on Wi-Fi on laptops

Enabling Wi-Fi on a laptop using the Fn + F5 keys

Usually on the keys responsible for connecting to the Network, there is a stylized image of the antenna. It doesn't matter which laptop is Acer or HP. You can always find such a button. But the combinations with it are different.

• Fn + F2 is a working combination for the Asus WiFi range.
• Fn + F12 must be pressed by those who purchased an HP laptop. Or there is a separate button that depicts a wireless network.
• Fn + F3 is a combination to enable WiFi communication for MSI models.
• For Samsung, there are two options: Fn + F12, or Fn + F9.
• Lenovo is different from HP or Acer. To establish a connection, mechanical switches are more commonly used in this range. But the Fn + F5 keys also work.
• F8 + Fn - keys that allow you to establish communication on any Toshiba laptop.
• The presence of a mechanical switch is typical for the Sony Vaio lineup.

You can look for a button that plays the role of a switch at the end of the device if Fn is absent. Did you manage to connect WiFi on the laptop, but something else does not work? Perhaps the problem lies in the WiFi settings of the Windows operating system.

What about software inclusion?

Sometimes special software is required to enable the adapter on a laptop. For Samsung models, the Easy Settings utility is responsible for this function. Intel PROSet is a program installed on almost any laptop from Intel. This must be taken into account if it was not possible to find a mechanical switch when the combinations indicated above do not work.

Establishing communication in the Windows operating system

Sometimes the adapter is built into the operating system from the very beginning, at the software level. Then turning on Wi-Fi is as easy as shelling pears, without any additional steps.

Open the desired item on the control panel, as shown in our picture. We need a button that offers to change the adapter and its parameters.

A list will appear in which there will be more than one adapter. We need one that has a Wireless or "Wireless network" postscript. This is the Wai Fay adapter itself, and we need to connect it to it.

In this case, users can face two situations.

1. Gray icon when adapter is off.
2. The adapter is colored, but there is a red cross on it.

More about the first issue

You need to click on the image with the right mouse button if the adapter is gray, or remains completely colorless. A context menu will appear, where we need to select the function of including Wai Fay. After that, an image should appear either with a working network, or with a red cross.

What about the second situation?

The device was able to connect, but the Wi-Fi network is not turned on.

Sometimes this happens due to the operating mode "in flight". In other situations, shutdown occurs in additional parameters. It is enough to right-click on the Wi-Fi icon to enable communication.
A separate window will pop up, where we need to select the function to enable "Wi-Fi". Or a wireless network. After everything is turned on, a list of available Wi-Fi networks will appear that you can work with. All that remains is to connect.

Checking the drivers. Are there any problems with them?

Sometimes it is not possible to set up a Wi-Fi network due to the fact that there are no drivers. Either when they are accidentally deleted by the user, or when they are not installed at all.

First, open the device manager. It's in the Windows Control Panel, under Hardware and Sound.
We need to see if there is any equipment with an exclamation mark next to it, yellow or red. This is especially true for the elements responsible for WiFi reception.

If there are problems, you will need to install drivers for WiFi.

About some connection settings

The wrong location of the router is a mistake that many users make. Because of this, WiFi is not as fast and stable as we would like. Even on quality Acer models. It is recommended to install routers at some distance from electronic household appliances. This is due to the operation of the devices at the same frequency as WiFi - 2.4 GHz. Because of this, on a laptop, WiFi speed decreases, even if it was possible to turn everything on according to the instructions.

Configuring WiFi for a local network

We connect the computer and the router with a cable. Before trying to configure or enable something, make sure that the connection has been established. If everything is in order, a corresponding image will appear next to the clock. This scheme works equally well for Acer models. HP and others.

In the properties of the connection, you must enter a specific set of data.

IP Address: 192.168.0.2 Subnet Mask: 255.255.255.0 Default Gateway: 192.168.0.1 DNS: 192.168.0.1

Some models' manuals may contain different information. We insert exactly what the accompanying documentation says. We open the command line to explore other possibilities. You can configure WiFi through the Start menu, just write “cmd” in the search box. In the command line that opens, type the combination ping 192.168.0.1. In response, packets will be received from this address, if everything went well. You need to find out what IP address the router accepts on the internal interface if a message appears that "the waiting limit has been exceeded." Otherwise, you will not be able to configure and turn on WiFi.

You can customize Wi-Fi by changing the last two digits if the limit message continues to appear.
1. 1.2
2. 1.1
3. 0.2

Go to the Wireles Settings section to configure Wi-Fi. After that, we need to name our own Weifai network. This is done in the Name (Ssid) line. In the Channel item, specify the Auto function, find your region from the list. Thanks to this solution, you can configure your Wi-Fi router so that it automatically searches for channels with the least amount of interference. Click on the Apply button to save what we were able to configure.

How to enable WiFi in Windows 8?

Setting up WiFi on this operating system is no more difficult than on others.

1. Choose Start, and then go to the Control Panel.
2. Click on the switch to the classic view. We find the center responsible for managing network connections. Here we will see a section with WiFi wireless connection.
3. Click on the utility with the right mouse button. And select the item with WiFi properties. There should be a line with automatic obtaining of an IP address. Press the OK button if there is a mark.
4. We return to the folder with the management of network connections. Again, you need the WiFi wireless network connection section. Click on it with the right mouse button, select the "connect-disconnect" item.
5. All that remains is to select and connect to the desired WiFi network.

The corresponding icons usually appear on the screen, in the right corner, at the bottom. If everything is done correctly, the WiFi image will always be active. If everything is in order with the network itself, it will always be possible to connect to it.

I will describe all the methods I know of turning on a Wi-Fi network on a laptop (after all, everything that can be turned off can be turned on and off ?!) I'll start with the simpler and more common methods, then I will move on to more complex methods that units will need.

So if you see on taskbar icon turned off Wi-Fi (or do not see the icon at all), then this article is for you.

Turn on Wi-Fi using a slider / button on the laptop case.

On many laptop models, to turn on Wi-Fi, you need to use the slider or a separate button to turn on Wi-Fi. This switch is often located on the front of the laptop.

The switch looks different, but has one function - turning the wireless network on and off.

To turn on Wi-Fi, simply move the slider to the On position.

How to turn on Wi-Fi using a keyboard shortcut.

If your laptop does not have sliders or separate Wi-Fi enable buttons, take a closer look at the keyboard, on it you can find the Wi-Fi icon on one of the function keys (F1-F12).

It can be located on different buttons, it all depends on the manufacturer and model of the laptop.

In order to turn on Wi-Fi, you must press this key or use the keyboard shortcut +<клавиша Wi-Fi>.

Consider the key combinations that are most commonly used in laptops from different manufacturers:

1. Acer... We hold down the keys: +.
2. Asus... Combination +.
3. HP... Click here +.
4. Lenovo... Needed buttons: +.
5. Samsung... Or +or +.
6. Dell keyboard shortcut +or +

How to turn on Wi-Fi in Windows settings.

If the specified procedures did not help and you are still wondering How do I turn on Wi-Fi on my laptop? you need to check if Wireless Network Connection is enabled in Windows settings. To do this, you need to go to the Network and Sharing Center. One way is to right-click on network icon in the lower right corner of the screen and select "Network and Sharing Center."

Another way to use hotkeys + enter command ncpa.cpl and press Enter.

It doesn't matter which of the methods you used, the result will be one - the Network Connections window will appear on the monitor. Next, you need to find a wireless connection, right-click on it and select "Enable" (if the Enable option is not available, then the Wi-Fi network is enabled).

Enabling Wi-Fi via Windows Device Manager.

If your Wi-Fi adapter is still not enabled, you need to check if it is enabled in the task manager. To do this, click the Start button, right-click Computer and select Manage. In the left menu, select Device Manager.

Or press the keyboard shortcut + in the search bar enter the command mmc devmgmt.msc and press Enter.

If the adapter icon is marked with an arrow down, it means it is disabled, in order to enable it, right-click on it and select "Enable".

Updating Wi-Fi drivers.

Another reason for the inoperability of Wi-Fi may be an inappropriate driver or its lack. In order to install the required driver, go to the website of the laptop manufacturer, find your model (on some sites it will be difficult to do this, you can write the laptop model in the comments, I will try to help you) and download the driver for the Wi-Fi network card for your operating system systems. After that, it will be enough to install the drivers, after restarting the laptop, Wi-Fi should work.

It doesn't matter which way you turned on the wireless network, in the end you should see the Wi-Fi icon in the taskbar. When you click on it, you will see the Wi-Fi networks available for connection.

Oddly enough, but this is the problem that often arises among users, new models of laptops. After a short use, for some unknown reason, Wi-Fi turns off. But this is done to reduce the power consumption of the battery. Today I will tell you how to quickly enable a wireless network or Wi-Fi adapter on laptops: HP, Lenova, ACEP, etc.

Diagnostics

To quickly fix the problem, simply find your network connection in the lower right corner. And it doesn't matter what kind of operating system you have Windows 7, 8, 10 or XP. Find the wave icon and right-click on it. Then select diagnostics.

The Windows operating system itself must find the problem and programmatically solve it. After that, you should see a phrase that the adapter has been disabled and the operating system has reactivated it.

But sometimes you can see this message: "Wireless disabled - Not fixed (With a red cross)." But do not be afraid, the system itself could not turn on the transmitter on the laptop, and we will do it manually.

Using the buttons

On 50% of laptops, you can find a separate button or switch that turns the Wi-Fi network on and off. For starters, I would look at the additional buttons next to the main keyboard. You need to find a button on which will be depicted: an antenna, a computer - with waves emanating from them.

If there is no such button, then you can look for it on the side of the laptop. Sometimes laptop companies put power buttons there. But as I wrote earlier, not all laptops have such a button. But you can turn it on in another way, for this you need to find a similar icon on the main keyboard in the row of F keys.

To activate, you must simultaneously press the auxiliary key "Fn" and this key. On my laptop, this is a combination of "Fn + F2", but sometimes they use the keys F3, F5, F9, F12.

If nothing happened when you clicked, then this means that you do not have drivers installed on your machine that are responsible for these buttons, so we will enable it in a different way.

Activation via the control center

1. Press the Win (It may look like a window) and R keys at the same time. You already know how to do this.

1. After that, you will see this window. It is necessary to enter the command ncpa.cpl in one field and click on the button below "OK".

1. Find the wireless connection with the ladder icon, right-click on it and select "Enable".

Windows 8 and 10

If you have an eight and a ten, then perhaps you have the "Airplane" mode turned on. Then there is no way you can turn on WiFi while it is working.

1. It is necessary to go to "All parameters".

1. Next, enter the section with the planet icon.

1. Click on the airplane and turn off the mode. You can also move the lower sliders to the "On" mode. Then, even if you have Airplane mode turned on, the wireless network and Bluetooth will not turn off.

Check driver

1. Press Win + R;

1. We register the devmgmt.msc command;

1. Go to the "Network Devices" section. Now take a close look - if there is an icon with an arrow down. If it is, then right-click on it and then select "Engage".

Checking the WLAN function

I must say right away that this function automatically controls all network devices and, in theory, it should be enabled. But sometimes, when installing some programs or in case of harm from viruses, the setting can fly off.

1. Win + R;

1. services.msc;

1. The list will arrange the data in alphabetical order. So just scroll down to the "WLAN Autoconfiguration Service" section. After that, select the properties of this section.

1. In the line "Startup type:" set automatic start. Then we press "Apply" and "OK".

Installing Drivers

If I were you, I would reinstall the drivers for your WiFi adapter. They should be downloaded from the official website of your laptop company.

1. To do this, connect the laptop to your router via a wire to any available LAN port. Or you can find where else you can use the Internet.

1. After that, open any search engine and enter the name of the company. I have an Acer laptop, so this is what I enter.

1. Choosing your product. We select the version of the operating system and then download the drivers for your wireless adapter.

If you did not find the necessary firewood on the site or are simply confused, then you can download a whole pack from the site - https://drp.su/ru/foradmin. You need to download "DriverPack Offline Network". After installing the driver, be sure to reboot the device.

What to do on the computer?

Unfortunately, manufacturers of conventional desktop personal computers do not install a built-in wireless network module. But you can buy it separately. It looks like a regular flash drive. Sometimes an antenna is also installed in it to improve communication. Such external modules cost from 800 to 1800 rubles in any computer store. Drivers are quickly installed offline the first time you connect to the internet.

Due to the lack of a single standard for a way to enable WiFi on laptops, even in a line of models from the same manufacturer, users often have problems how to enable WiFi on a laptop, for example, from the popular HP brand. Below is a detailed guide describing how to activate the WiFi adapter on HP laptops.

Preparatory actions

Before turning on Wi-Fi on a laptop, you need to make sure that you have correctly installed software for the normal functioning of the WiFi adapter built into the device. The installation of hardware drivers can be checked using the Network and Sharing Center or through the device manager.

It will take just a few sequential steps:

To solve the problem through the "Device Manager", you should take the following steps (for example, Windows 10):

As in the above instructions, you will also need to visit the official resource of the equipment manufacturer on the Internet, download the appropriate drivers for the adapter from there and then install them into the laptop.

Weifai activation procedure

The inclusion can be done in several ways.

Method 1: Using HP Connection Manager

The algorithm of actions consists of the following steps:

Method 2: Using the buttons on an HP laptop

Most often in models of laptops of the HP brand, a combination of buttons on the keyboard is used. For example, you need to hold down "Fn" and click on "F12". Sometimes, instead of "F12", another button is provided, but this key always has a picture with a WiFi symbol.

There are HP laptops equipped with special buttons that perform the function of activating the Wafi adapter. For example, in earlier models such a key was located above the keyboard, and in some subsequent models, the manufacturer began to place it below the keyboard.

Often there are modern models in which the method of activating WiFi is implemented by means of a touch button, which is indicated by the characteristic icon of the Wi-Fi wireless network. Sometimes there is an “X” next to the symbol representing the wireless network. If this symbol is active, then the Weifai is in the off state.

The presence of Wi-Fi makes it possible to use the Internet in a variety of places. But before you can, comfortably sitting in a cafe or on a park bench, plunge into the world of the Internet, you need to deal with your laptop and find how and where to turn on the network on your laptop.

There is nothing difficult about turning on the wireless connection on a laptop. You just need to know the function keys to enable wireless communication on a laptop of your brand, because each manufacturer plays up the key combinations in their own way. For those who are trying to understand:

• how to enable wireless communication on an Asus laptop, you just need to press Fn and F2;
• The wireless button on an HP laptop is a combination of Fn and F12, or a touch-sensitive button with an antenna pattern on models where it is available;
• on Lenovo, press Fn and F5 or a special switch, which is indicated in the instructions;
• Acer and Packard Bell turn on the network by combining Fn and F3;
• on different Samsung models it is either Fn and F9 or Fn and F12.

If the standard combinations are not suitable (in new models another may be introduced), then attention should be paid to the instructions from the manufacturer, which must indicate all the necessary information related to the functionality of the laptop. In any case, it should be the Fn button, and in its absence, a special button with an antenna pattern or a switch is pressed.

Turn on wireless on your laptop in other ways

If the switch is not marked on the keyboard, it can be moved to the side panel or the bottom of the laptop. The buttons located on the lower part are made invisible, so you need to take special care to find it there. If neither the combination nor the switch could turn on the wireless network, then most likely the wi-fi is simply not configured, and it's time to do it.

How do I turn on the wireless adapter?

Any setup begins with checking for the presence of the necessary drivers, which are connected, if any, but not connected, and are first downloaded and installed, and then connected if they are not in the laptop. You can check the drivers through the "Control Panel", menu item "Device Manager". If this subsection is not immediately visible, then perhaps it is in the "Hardware and Sound" section.

From the "Dispatcher" you need to go to the "Network Adapters" and find the Wireless section there, which is the right one. It may be that there is no inscription, or it is marked with an exclamation mark. This is a direct indication of a driver problem that will need to be installed first. They must be present on the disc that came with the laptop. If the disk is lost or for some reason the installation fails, you can look for them on the manufacturer's website.

If there are drivers, but are marked with an exclamation mark, then you need to right-click on this icon and select the appropriate item in the menu that appears. This is usually the phrase "Engage." It may be necessary to enable it additionally if the adapter is connected to the power saving mode.

You can eliminate the saving factor in the windows 7 menu in the "Properties" section, where there should be a subsection "Power management". It has a check mark on the item "Allow shutdown to save".

After unchecking the box, the drivers will work, and the connection can be made by standard keystrokes. If the above manipulations do not bring results, the laptop must be shown to a specialist - it may be damaged.

strana-sovetov.com

How to enable wireless networking on a laptop

A wireless Wi-Fi network is the ease and convenience of surfing the Internet wherever you have access to it. But sometimes many people face the problem of connecting a laptop to a Wi-Fi network. In most cases it is easy to fix, but sometimes you have to make certain adjustments.

Wireless Internet in some laptops is turned on using a button with an antenna image. You should look for it on the case of the device.

Most newer laptop models do not have a separate power button. Then the wireless Internet must be turned on by pressing a certain key combination:

• Asus - "Fn" - "F2";
• MSI - "Fn" - "F10";
• Acer - "Fn" - "F3";
• HP - "Fn" - "F12";
• Lenovo - "Fn" - "F5";
• Samsung - "Fn" - "F9" or "Fn" - "F12".

If an external adapter is used to connect to the network, then it must be connected to the laptop via the USB port.

If the laptop has a built-in Wi-Fi adapter, then in order to connect to a wireless network, you need to enable it in the windows settings. To do this, press the "Win" - "R" keys, then enter "ncpa.cpl" in the window. The section "Changing adapter settings" (or "Network connections") contains "Wireless network connection". If it is gray, then you need to right-click on it and select "Enable".

Due to a failure, the Wi-Fi adapter may be disabled in the Device Manager. If this happens, then in the "Network Connections" icon "Wireless network connection" will be absent. To fix this problem, you need to press the "Win" - "R" keys, enter "devmgmt.msc" in the pop-up window. In the "Device Manager" select the "Network adapters" section and find a Wi-Fi or Wireless device. Click on it with the right mouse button and select "Engage". If you cannot turn on the device, you need to download and install drivers for the Wi-Fi adapter.

Sometimes it is necessary to independently enter the parameters of a network that works in a hidden mode. To do this, you need to open the "Network and Sharing Center", select "Manage wireless networks", "Add" and then "Create a network profile manually." Enter the required parameters in the table, click "Next" and "Connect".

Sometimes you can find laptops in which to connect to a wireless network, you first need to launch the "Wireless Assistant" or "Wi-Fi Manager" buttons located in the "Start" menu. Then you can turn on Wi-Fi without hindrance.

SovetClub.ru

Enabling and configuring Wi-Fi on laptops with different versions of windows

Laptop owners usually use a wireless connection to access the Internet, since there is a Wi-Fi adapter on all laptop models without exception. However, in order to use it, sometimes you have to figure out how to turn on wifi on a laptop.

Hotkeys or hardware switch

The first step is to physically turn on the Wi-Fi adapter. On different laptop models, this procedure is slightly different, but its meaning is the same: you need to find a hardware switch or use the function keys. Let's look at a few examples:

You can go on with the options for enabling Wi-Fi for a long time, giving ways for MSI, Acer, Samsung and other brands. Even different series of the same manufacturer have different ways to activate the wireless module from each other, therefore:

• Examine the laptop case for a hardware switch or Wi-Fi power button.
• Examine the keyboard - one of the keys in the F1-F12 row should be marked with a wireless icon. If you press it together with the Fn button, the adapter turns on or off.

If you have a laptop of the Sony Vaio series, then there may not be a hardware key or an Fn button on its keyboard. For Wi-Fi to work in this case, a special VAIO Smart Network utility is required, which can be found on the manufacturer's official website.

Fn button does not work

What if the Fn button doesn't work? How do you enable the adapter in this case? First you need to figure out why the key is not working. Fn runs under BIOS control and has its own utility, without which the key does not function. Therefore, if the button does not work, first you need to find on the manufacturer's website a utility for enabling hot keys for a specific laptop model (the name should contain the word “HotKey”).

If the installation of the utility did not help or the key is physically damaged, then you will have to use an alternative method to turn on the adapter. On windows 8 and windows 10, to enable the adapter, just click on the Wi-Fi icon in the notification bar and move the "Wireless network" slider to the active position. If the adapter drivers are installed correctly, then the icon must be present.

In windows 7, there is no such function, but you can try to enable the wireless connection through the window for changing adapter parameters (described below). If this method did not help, then you will have to look for an external keyboard with a working Fn key and then no longer turn off the Wi-Fi module.

Setting up Wi-Fi on different versions of windows

You will figure out the physical inclusion of the module quickly enough. Sometimes this completes the Wi-Fi setup: the system performs the rest of the necessary actions on its own, displaying a list of available wireless points. But sometimes you have to establish a connection manually.

Regardless of the version of windows, first you need to check that the drivers for the Wi-Fi module were installed without errors:

To be sure, it is better to go to the official website of the laptop manufacturer and find the latest version of the wireless module driver for your model. In addition, right-click on the adapter and select "Enable" (if it is stopped).

windows XP

In theory, windows XP should have stopped using a long time ago, but on some older Dell models and other laptops, the legendary system still continues to perform its functions. Wi-Fi in windows XP is configured as follows:

1. Check that the Wi-Fi indicator on the laptop is on (that is, you turned on the adapter and installed the drivers).
2. Open "Control Panel".
3. Find the "Network Connections" section.

There should be a "Wireless Network Connection" icon in the Explorer window. Its presence demonstrates that the Wi-Fi module is working correctly. Right-click the icon and select Enable. Further:

If the list of available points does not contain the network that your router distributes, click "Refresh List". Then select the desired point by name and click "Connect". If the network is password protected, you will be prompted to enter the access code, after which the connection will be established.

windows 7

On windows 7, the procedure for connecting to a wireless network has changed slightly, becoming a little easier. Now all available networks are displayed after clicking on the Wi-Fi icon in the system tray. But if there is no icon, then:

1. Go to the Network Sharing Center.
2. Click "Change adapter settings".
3. Find a wireless connection and make sure it's turned on.

After turning on the wireless connection, the Wi-Fi icon will appear in the tray. Click on it to see a list of available points, select a network and click "Connect".

windows 8

On windows 8, the procedure for connecting to Wi-Fi remained the same, but the "Airplane" mode was added, with which you need to be able to work. If the adapter driver is installed and the wireless connection is working correctly, then you will see the Wi-Fi icon in the notification panel, when you click on it, a list of available networks appears.

If there is no icon, follow the same steps as on windows 7 - open the "Change adapter settings" window and enable the wireless connection. If there is no wireless connection itself, check the drivers and the status of the module - everything should be turned on and installed.

If the adapter is turned on, the drivers are installed, but no available networks are found, check that the Airplane mode icon is not displayed in the notification bar. If there is one, you need to disable this mode. To do this, click on the icon and move the slider to the "Disabled" state.

windows 10

On windows 10, everything remains the same with minor changes, so you will quickly figure out how to connect your laptop to Wi-Fi:

1. Click on the wireless icon in the tray.
2. Select the desired network.
3. Click "Connect" and enter your password.

If the access point is not displayed, try adjusting the network settings. Click on the link of the same name - the "Network and Internet" section of the windows 10 settings will open.

There are two tabs you are interested in here:

• Wi-Fi - Make sure the wireless network is turned on.
• Airplane mode - make sure the mode is disabled.

You can go to the section for changing adapter parameters and enable the wireless connection. Simply put, on windows 10 you have several equivalent options - you just need to choose a more convenient method for yourself.